Preliminary W742E81A/W742C81A

4-BIT MICROCONTROLLER

Publication Release Date: April 2000

- 1 - Revision A1

1. GENERAL DESCRIPTION

The W742E81A/W742C81A is a high-performance 4-bit microcontroller (

C) that provides an LCD

driver. The device contains a 4-bit ALU, two 8-bit timers, two dividers (for two oscillators) in dual-
clock operation, a 40

4 LCD driver, six 4-bit I/O ports (including 1 output port for LED driving), and

one channel DTMF generator. There are also five interrupt sources and 16-levels subroutine nesting
for interrupt applications. The W742E81A/W742C81A operates on very low current and has two
power reduction modes, that is the dual-clock slow operation and STOP mode, which help to
minimize power dissipation.

2. FEATURES

Operating voltage: 2.4V

3.8V

Dual-clock operation or single-clock operation (By option)

Main-oscillator

Connect to 3.58 MHz crystal or 400 KHz that can be selected by option code

Crystal or RC oscillator can be selected by code option (W742E81A)

Connect to 2 MHz typical RC oscillator (W742C81A)

Sub-oscillator

Connect to 32768 Hz crystal only

Memory

16384 x 16 bits program flash EEPROM (including 64K x 4 bit look-up table)

2048 x 4 bits data RAM (including 16 nibbles x 16 pages working registers)

40 x 4 LCD data RAM

24 input/output pins

Port for input only: 1 ports/4 pins(RC)

Input/output ports: 3 ports/12 pins(RA, RB & RD)

High sink current output port for LED driving: 1 port /4 pins(RE)

Port for output only: 1 port/ 4 pins(RF)

Power-down mode

Hold function: no operation (main-oscillator and sub-oscillator still operate)

Stop function: no operation (main-oscillator and sub-oscillator are stopped)

Dual-clock slow operation mode: system is operated by the sub-oscillator (F

OSC

=Fs and Fm is

stopped)

Five types of interrupts

Four internal interrupts (Divider0, Divider1, Timer 0, Timer 1)

One external interrupts (RC Port)

Preliminary W742E81A/W742C81A

- 2 -

LCD driver output

40 segments x 4 commons

1/4 duty 1/3 bias driving mode

Clock source should be the sub-oscillator clock in the dual-clock operation mode

MFP output pin

Output is software selectable as modulating or nonmodulating frequency

Works as frequency output specified by Timer 1

DTMF output pin

Output is one channel Dual Tone Multi-Frequency signal for dialling

Two built-in 14-bit frequency dividers

Divider0: the clock source is the output of the main-oscillator

Divider1: the clock source is the output of the sub-oscillator (dual-clock mode) or the Fosc/128

(single-clock mode)

Two built-in 8-bit programmable countdown timers

Timer 0: one of two internal clock frequencies (F

OSC

/4 or F

OSC

/1024) can be selected

Timer 1: with auto-reload function and one of three internal clock frequencies (F

OSC,

OSC

/64 or

Fs) can be selected by MR1 register; and the specified frequency can be delivered to MFP pin

Built-in 18/15-bit watchdog timer selectable for system reset; enable the watch dog timer or not is

determined by code option

Powerful instruction set: 142 instructions

16-levels subroutine (include interrupt) nesting

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 3 - Revision A1

3. PIN CONFIGURATION

For W742E81A

80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62

9 10 11 12 13 14 15 16 17 18 19

RC1

RC0

RB3

RB2

RB1

RB0

RA3

RA1

SEG31

SEG30

SEG29

SEG28

SEG27

SEG26

SEG25

SEG24

SEG23

R
E

SEG22

SEG21

SEG20

SEG19

RA0

RA2

20 21 22 23 24

61 60 59 58 57

N
C

RD0

RC3

RC2

25 26 27 28 29

56 55 54 53 52

RD2

RD1

100

RD3

SEG18

SEG17

SEG16

SEG15

N
C

R
E

R
F

V
S
S

S
E
G

S
E
G
3

S
E

S
E
G

1
1

S
E
G

1
2

S
E

G
1
3

S
E
G
3
3

S
E
G
3
4

S
E
G
3
5

S
E
G
3
6

S
E
G
3
7

S
E
G
3
8

S
E
G
3
9

C
O
M
3

C
O
M
2

C
O
M
1

C
O
M
0

V
D
D
2

V
D
D
1

D
H
2

D
H
1

X
O
U
T
2

X
I
N
2

V
D
D

X
O
U
T
1

X
I
N
1

D
T
M
F

R
E
S

N
C

S
E

G
1
4

S
E
G
3
2

MFP

N
C

Preliminary W742E81A/W742C81A

- 4 -

For W742C810

80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62

1 2

3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

RC1

RC0

RB3

RB2

RB1

RB0

RA3

RA1

SEG31

SEG30

SEG29

SEG28

SEG27

SEG26

SEG25

SEG24

SEG23

R
E

SEG22

SEG21

SEG20

SEG19

RA0

RA2

20 21 22 23 24

61 60 59 58 57

N
C

RD0

RC3

RC2

25 26 27 28 29

56 55 54 53 52

RD2

RD1

100

RD3

SEG18

SEG17

SEG16

SEG15

N
C

R
E

R
F

F
2

R
F

V
S
S

S
E
G

S
E

G
8

S
E

G
9

S
E
G

1
1

S
E
G

1
2

S
E

G
1
3

N
C

S
E
G
3
3

S
E
G
3
4

S
E
G
3
5

S
E
G
3
6

S
E
G
3
7

S
E
G
3
8

S
E
G
3
9

C
O
M
3

C
O
M
2

C
O
M
1

C
O
M
0

V
D
D
2

V
D
D
1

D
H
2

D
H
1

X
O
U
T
2

X
I
N
2

V
D
D

X
O
U
T
1

X
I
N
1

D
T
M
F

R
E

N
C

MFP

N
C

RE0

N
C

SEG14

N
C

SEG32

N
C

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 5 - Revision A1

4. PIN DESCRIPTION

SYMBOL

I/O

FUNCTION

XIN2

Input pin for sub-oscillator.
Connected to 32.768 KHz crystal only.

XOUT2

Output pin for sub-oscillator with internal oscillation capacitor. Connected
to 32.768 KHz crystal only.

XIN1

Input pin for main-oscillator.
Connected to 3.58 MHz or 400 KHz crystal or RC to generate system
clock.

XOUT1

Output pin for main-oscillator.
Connected to 3.58 MHz or 400 KHz crystal or RC to generate system
clock.

RA0

RA3

I/O Input/Output port.

Input/output mode specified by port mode 1 register (PM1).

RB0

RB3

I/O Input/Output port.

Input/output mode specified by port mode 2 register (PM2).

RC0

RC3

4-bit port for input only.

Each pin has an independent interrupt capability.

RD0

RD3

I/O Input/Output port.

Input/output mode specified by port mode 5 register (PM5).

RE0

RE3

Output port only. With high sink current capacity for the LED application.

RF0

RF3

Output port only.

MFP

Output pin only.

This pin can output modulating or nonmodulating frequency, or Timer 1
specified frequency. It can be selected by bit 0 of BUZCR (BUZCR.0).

DTMF

This pin can output dual-tone multifrequency signal for dialling.

RES

System reset pin with pull-high resistor.

SEG0

SEG39

LCD segment output pins.

COM0

COM3

LCD common signal output pins.

The LCD alternating frequency can be selected by code option.

DH1, DH2

Connection terminals for voltage doubler (halver) capacitor.

DD1

DD2

Positive (+) supply voltage terminal.

Refer to Functional Description.

Positive power supply (+).

Negative power supply (-).

Preliminary W742E81A/W742C81A

- 6 -

Pin Description, continued

SYMBOL I/O

FUNCTION

Voltage control pin for the flash EEPROM programming, erasing and verifying.
This pin has the built-in pull-low resistor.

MODE

This pin can be used as mode selection control; data read/write clock;
program/erase control or address counter control in the flash EEPROM erasing,
programming or verifying mode. This pin has the built-in pull-low resistor.

DATA

I/O Data I/O pin with the built-in pull-low resistor.

5. BLOCK DIAGRAM

LCD DRIVER

STACK

(16 Levels)

RAM

(2048*4)

ALU

Timer 0

(8 Bit)

Timing Generator

PORT RA

PORT RB

PORT RC

Modulation
Frequency
Pulse

SEG0~SEG39

COM0~COM3

RA0-3

RB0-3

RC0-3

RD0-3

MFP

XIN1 XOUT1 XIN2

XOUT2

VDD

VSS

VDD1-2

DH1-2

Flash
EEROM

(16384*16)

(look_up table
64K*4)

Timer 1

(8 Bit)

ACC

RES

Divider 0

(14 Bit)

Watch Dog Timer

(4 Bit)

HCF

PEF

HEF

IEF

Central

Control

Unit

EVF

SEF

PSR0

SCR

MR0

MR1

PORT RE

MUX

SEL

+1(+2)

PORT RD

PM0

Divider 1

(12/14 Bit)

RE0-3

PORT RF

RF0-3

DTMF

Generator

DTMF

PM1

DTMF

DTCR

VPP

DATA

MODE

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 7 - Revision A1

6. FUNCTIONAL DESCRIPTION

6.1 Program Counter (PC)

Organized as an 14-bit binary counter (PC0 to PC13), the program counter generates the addresses
of the 16384

16 on-chip ROM containing the program instruction words. Before the jump or

subroutine call instructions are to be executed, the destination ROM page must be determined firstly.
The confirmation of the ROM page can be done by executing the MOV ROMPR, #I or MOV ROMPR,
R instruction. When the interrupt or initial reset conditions are to be executed, the corresponding
address will be loaded into the program counter directly. The format used is shown below.

Table 1 Vector address and interrupt priority

ITEM

ADDRESS

INTERRUPT PRIORITY

Initial Reset

0000H

INT 0 (Divider0)

0004H

1st

INT 1 (Timer 0)

0008H

2nd

INT 2 (Port RC)

000CH

3rd

INT 3 (Divider1)

0014H

4th

INT 4 (Timer 1)

0020H

5th

JP Instruction

XXXXH

Subroutine Call

XXXXH

6.2 Stack Register (STACK)

The stack register is organized as 49 bits x 16 levels (first-in, last-out). When either a call subroutine
or an interrupt is executed, the program counter will be pushed onto the stack register automatically.
At the end of a call subroutine or an interrupt service subroutine, the RTN instruction must be
executed to pop the contents of the stack register into the program counter. (Refer to Table 8)
When the stack register is pushed over the sixteen levels, the contents of the first level will be lost. In
other words, the stack register is always sixteen levels deep.

6.3 Program Memory (ROM)

The read-only memory (ROM) is used to store program codes; and the look-up table is arranged as
65536 x 4 bits. The program ROM is divided into eight pages; the size of each page is 2048 x 16 bits.
So the total ROM size is 16384 x 16 bits. Before the jump or subroutine call instructions are to be
executed, the destination ROM page must be determined firstly. The ROM page can be selected by
executing the MOV ROMPR,#I or MOV ROMPR, R instruction. But the branch decision instructions
(e.g. JB0, SKB0, JZ, JC, ...) must jump to the same ROM page which the branch decision instructions
are in. The whole ROM can store both instruction codes and the look-up table. Each look-up table
element is composed of 4 bits, so the look-up table can be addressed up to 65536 elements.
Instruction MOVC R is used to read the look-up table content and transfer table data to the RAM. But
before reading the addressed look-up table content, the content of the look-up table pointer (TAB)
must be determined firstly. The address of the look-up table element is allocated by the content of
TAB. The MOV TAB0 (TAB1, TAB2, TAB3), R instructions are used to allocate the address of the
wanted look-up table element. The TAB0 register stores the LSB 4 bits of the look-up table address.

Preliminary W742E81A/W742C81A

- 8 -

The organization of the program

memory is shown in Figure 6-1

0000H

16 bits

16384 x 16 bits

07FFH

0400H

Each element (4 bits) of the look-up table

03FFH

0800H

0FFFH

0C00H

0BFFH

1st page

3C00H

3BFFH

3800H

3FFFH

2nd page

8th page

Look-up table address:

0000H

0FFFH

Look-up table address:

1000H

1FFFH

Look-up table address:

2000H

2FFFH

Look-up table address:

3000H

3FFFH

Look-up table address:

E000H

EFFFH

Look-up table address:

F000H

FFFFH

Figure 6-1 Program Memory Organization

6.3.1 ROM Page Register (ROMPR)

The ROM page register is organized as a 4-bit binary register. The bit descriptions are as follows:

ROMPR

Note: W means write only.

Bit 3 is reserved.

Bit 2, Bit 1, Bit 0 ROM page preselect bits:

000 = ROM page 0 (0000H - 07FFH)
001 = ROM page 1 (0800H - 0FFFH)
010 = ROM page 2 (1000H - 17FFH)
011 = ROM page 3 (1800H - 1FFFH)
100 = ROM page 4 (2000H - 27FFH)
101 = ROM page 5 (2800H - 2FFFH)
110 = ROM page 6 (3000H - 37FFH)
111 = ROM page 7 (3800H - 3FFFH)

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 9 - Revision A1

6.4 Data Memory (RAM)

6.4.1 Architecture

The static data memory (RAM) used to store data is arranged as 2048

4 bits. The data RAM is

divided into sixteen banks; each bank has 128

4 bits. Executing the MOV DBKR,WR or MOV

DBKR,#I instruction can determine which data bank is used. The data memory can be addressed
directly or indirectly. But the data bank must be confirmed firstly; and the page in the data bank will
be done in the indirect addressing mode, too. In indirect addressing mode, each data bank will be
divided into eight pages. Before the data memory is addressed indirectly, the page which the data
memory is in must be confirmed. The organization of the data memory is shown in Figure 6-2.

1st data bank

2048

addresses

000H

4 bits

2048 * 4 bits

07FH
080H

0FFH

2nd data bank

780H

7FFH

16th data bank

(or Working Registers bank)

00H

0FH
10H

1FH
20H

2FH

70H

7FH

:
:

1st data RAM page

(or 1st WR page)

2nd data RAM page

(or 2nd WR page)

8th data RAM page

(or 8th WR page)

3rd data RAM page

(or 3rd WR page)

(or Working Registers bank)

3rd data bank

Figure 6-2 Data Memory Organization

The 1st and 2nd data bank (00H to 7FH & 80H to FFH) in the data memory can also be used as the
working registers (WR). It is also divided into sixteen pages. Each page contains 16 working registers.
When one page is used as WR, the others can be used as the normal data memory. The WR page
can be switched by executing the MOV WRP,R or MOV WRP,#I instruction. The data memory cannot
operate directly with immediate data, but the WR can do. The relationship between data memory
locations and the page register (PAGE) in indirect addressing mode is described in the next sub-
section.

6.4.2 Page Register (PAGE)

The page register is organized as a 4-bit binary register. The bit descriptions are as follows:

R/W

PAGE

Note: R/W means read/write available.

Bit 3 is reserved.

Bit 2, Bit 1, Bit 0 Indirect addressing mode preselect bits:

000 = Page 0 (00H - 0FH)

Preliminary W742E81A/W742C81A

- 10 -

001 = Page 1 (10H - 1FH)
010 = Page 2 (20H - 2FH)
011 = Page 3 (30H - 3FH)
100 = Page 4 (40H - 4FH)
101 = Page 5 (50H - 5FH)
110 = Page 6 (60H - 6FH)

111 = Page 7 (70H - 7FH)

6.4.3 WR Page Register (WRP)

The WR page register is organized as a 4-bit binary register. The bit descriptions are as follows:

R/W

WRP

R/W

Note: R/W means read/write available.

Bit 3, Bit 2, Bit 1, Bit 0 Working registers page preselect bits:

0000 = WR Page 0 (00H - 0FH)

0001 = WR Page 1 (10H - 1FH)

0010 = WR Page 2 (20H - 2FH)

0011 = WR Page 3 (30H - 3FH)

0100 = WR Page 4 (40H - 4FH)

0101 = WR Page 5 (50H - 5FH)

0110 = WR Page 6 (60H - 6FH)

0111 = WR Page 7 (70H - 7FH)

1000 = WR Page 8 (80H - 8FH)

1001 = WR Page 9 (90H - 9FH)

1010 = WR Page A (A0H - AFH)

1011 = WR Page B (B0H - BFH)

1100 = WR Page C (C0H - CFH)

1101 = WR Page D (D0H - DFH)

1110 = WR Page E (E0H - EFH)

1111 = WR Page F (F0H - FFH)

6.4.4 Data Bank Register (DBKR)

The data bank register is organized as a 4-bit binary register. The bit descriptions are as follows:

R/W

DBKR

R/W

Note: R/W means read/write available.

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 11 - Revision A1

Bit 3, Bit 2, Bit 1, Bit 0 Data memory bank preselect bits:

0000 = Data bank 0 (000H - 07FH)

0001 = Data bank 1 (080H - 0FFH)

0010 = Data bank 2 (100H - 17FH)

0011 = Data bank 3 (180H - 1FFH)

0100 = Data bank 4 (200H - 27FH)

0101 = Data bank 5 (280H - 2FFH)

0110 = Data bank 6 (300H - 37FH)

0111 = Data bank 7 (380H - 3FFH)

1000 = Data bank 8 (400H - 47FH)

1001 = Data bank 9 (480H - 4FFH)

1010 = Data bank A (500H - 57FH)

1011 = Data bank B (580H - 5FFH)

1100 = Data bank C (600H - 67FH)

1101 = Data bank D (680H - 6FFH)

1110 = Data bank E (700H - 77FH)

1111 = Data bank F (780H - 7FFH)

6.5 Accumulator (ACC)

The accumulator (ACC) is a 4-bit register used to hold results from the ALU and transfer data
between the memory, I/O ports, and registers.

6.6 Arithmetic and Logic Unit (ALU)

This is a circuit which performs arithmetic and logic operations. The ALU provides the following
functions:

Logic operations: ANL, XRL, ORL

Branch decisions: JB0, JB1, JB2, JB3, JNZ, JZ, JC, JNC, DSKZ, DSKNZ, SKB0, SKB1, SKB2,

SKB3

Shift operations: SHRC, RRC, SHLC, RLC

Binary additions/subtractions: ADC, SBC, ADD, SUB, ADU, DEC, INC

After any of the above instructions are executed, the status of the carry flag (CF) and zero flag (ZF) is
stored in the internal registers. CF can be read out by executing MOV R, CF.

6.7 Main-Oscillator

The W742E81A/W742C81A provides a crystal or RC oscillation circuit to generate the system clock
through external connections. If a crystal oscillator is used, The 3.58 MHz or 400KHz crystal must
be connected to XIN1 and XOUT1, and a capacitor must be connected to XIN1 and V

if an accurate

frequency is needed.

Preliminary W742E81A/W742C81A

- 12 -

XIN1

XOUT1

Crystal

3.58 MHz

400 KHz

XIN1

XOUT1

Figure 6-3 System Clock Oscillator Configuration

6.8 Sub-Oscillator

The sub-oscillator is used in dual-clock operation mode. In the sub-oscillator application, just only the
32768 Hz crystal could be connected to XIN2 and XOUT2, and it would not be oscillated in STOP
mode.

6.9 Dividers

Each divider is organized as a 14-bit binary up-counter designed to generate periodic interrupts.
When the main oscillator starts action, the Divider0 is incremented by each clock (F

OSC

). When an

overflow occurs, the Divider0 event flag is set to 1 (EVF.0 = 1). Then, if the Divider0 interrupt enable
flag has been set (IEF.0 = 1), the interrupt is executed, while if the hold release enable flag has been
set (HEF.0 = 1), the hold state is terminated. And the last 4-stage of the Divider0 can be reset by
executing CLR DIVR0 instruction.

If the sub-oscillator starts action, the Divider1 is incremented by each clock (Fs in dual-clock mode or
Fosc/128 in single-clock mode). When an overflow occurs, the Divider1 event flag is set to 1 (EVF.4
= 1). Then, if the Divider1 interrupt enable flag has been set (IEF.4 = 1), the interrupt is executed,
while if the hold release enable flag has been set (HEF.4 = 1), the hold state is terminated. And the
last 4-stage of the Divider1 can be reset by executing CLR DIVR1 instruction. Same as EVF.0, the
EVF.4 is set to 1 periodically. But there are two period time (125 mS & 500mS) that can be selected
by setting the SCR.3 bit. When SCR.3 = 0 (default), the 500 mS period time is selected; SCR.3 = 1,
the 125 mS period time is selected.

6.10 Dual-clock operation

This operation mode is selected by option code. In the dual-clock mode, the clock source of the LCD
frequency selector should be the sub-oscillator clock (32768 Hz) only. But in the signal-clock mode,
the clock source of the LCD frequency selector will be Fm/128(Fm : main oscillator clock, See figure
6-4).

So before the STOP instruction is executing, the LCD must be turned off in the signal-

clock mode or dual-clock mode.

In this dual-clock mode, the normal operation is performed by generating the system clock from the
main-oscillator clock (Fm). As required, the slow operation can be performed by generating the
system clock from the sub-oscillator clock (Fs). The exchange of the normal operation and the slow
operation is performed by resetting or setting the bit 0 of the System clock Control Register (SCR). If
the SCR.0 is reset to 0, the clock source of the system clock generator is main-oscillator clock; if the
SCR.0 is set to 1, the clock source of the system clock generator is sub-oscillator clock. In the dual-
clock mode, the main-oscillator can stop oscillating when the STOP instruction is executing or the
SCR.1 is set to 1.

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 13 - Revision A1

When the SCR is set or reset, we must care the following cases:

1. X000B

X011B: we should not exchange the F

OSC

from Fm into Fs and disable Fm

simultaneously. We could first exchange the F

OSC

from Fm into Fs, then disable the main-

oscillator. So it should be X000B

X001B

X011B.

2. X011B

X000B: we should not enable Fm and exchange the F

OSC

from Fs into Fm

simultaneously. We could first enable the main-oscillator; the 2nd step is calling a delay subroutine
to wait the main-oscillator oscillating stably; then exchange the F

OSC

from Fs into Fm is the last

step. So it should be X011B

X001B

delay the Fm oscillating stably time

X000B. The

suggestion of the Fm oscillating stably time is 3.5 mS for 455 KHz and 0.8ms for 4 MHz.

We must remember that the X010B state is inhibitive, because it will induce the system shutdown.

The organization of the dual-clock operation mode is shown in Figure 6-4.

System Clock

Generator

Main Oscillator

XIN1

XOUT1

Sub-Oscillator

XIN2

XOUT2

Fosc

Divider 0

SCR : System clock Control Register ( default = 00H )

Bit0

Bit1

Bit3

0 : Fosc = Fm

1 : Fosc = Fs

0 : Fm enable

1 : Fm disable

enable/disable

SCR.1

STOP

HOLD

SCR.0

LCD Frequency

Selector

LCD

Divider 1

INT4
HCF.4

SCR.3(14/12 bit)

1 : 12 bit

0 : 14 bit

Daul clock operation mode :

- SCR.0=0, Fosc=Fm : SCR.0=1, Fosc=Fs

- Flcd=Fs, In STOP mode LCD work continue.

Fosc/128

Dual/Single Colck

Option code is 1/0

Fs or Fosc/128

Figure 6-4 Organization of the dual-clock operation mode

Preliminary W742E81A/W742C81A

- 14 -

6.11 WatchDog Timer (WDT) and WatchDog Timer Register(WDTR)

The watchdog timer (WDT) is organized as a 4-bit up counter designed to prevent the program from
unknown errors. When the corresponding option code bit of the WDT set to 1, the WDT is enabled,
and if the WDT overflows, the chip will be reset. At initial reset, the input clock of the WDT is
F

OSC

/2048. The input clock of the WDT can be switched to F

OSC

/16384 (or F

OSC

/2048) by setting

WDTR.3 to 1. The contents of the WDT can be reset by the instruction CLR WDT. In normal
operation, the application program must reset WDT before it overflows. A WDT overflow indicates
that operation is not under control and the chip will be reset. The WDT overflow period is 1 S when
the sub-system clock (Fs) is 32 KHz and WDT clock input is Fs/2048. When the corresponding option
code bit of the WDT set to 0, the WDT function is disabled. The organization of the Divider0 and
watchdog timer is shown in Figure 6-5.

Q10 Q11 Q12

Q14

Q13

Fosc

HEF.0

IEF.0

1. Reset

2. CLR EVF,#01H

EVF.0

Hold mode release

(HCF.0)

Divider interrupt (INT0)

...

Overflow signal

WDT

Enable

Disable

WDTR.3

Fosc/2048

Fosc/16384

Option code is "0"

Qw1

Qw2

Qw4

Qw3

Divider0

System Reset

1. Reset

2. CLR WDT

3. CLR DIVR0

Option code is "1"

WDTR.2

Q10 Q11 Q12

Q14

Q13

HEF.4

IEF.4

Reset

EVF.4

Hold mode release

(HCF.4)

Divider interrupt

(INT1)

...

Divider1

Fss/2048

Fss/16384

2. CLR EVF,#10H
3. CLR DIVR1

Fss=Fs or Fosc/128

SCR.3

Figure 6-5 Organization of Divider0, Divider1 and WatchDog Timer

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 15 - Revision A1

WDTR

R/W

Note: R/W means read/write available, R means read only.
Power On reset default is : 0000

Bit 3 = 0 F

OSC/

2048(Select Divider0) or Fss/2048(Select Divider1) as the WDT source.

= 1 F

OSC/

16384(Select Divider0) or Fss/16384(Select Divider1) as the WDT source.

Bit 2 = 0 Select Divider0.
= 1 Select Divider1.
Bit 1 = 0 Refer to Table 2.
= 1 Refer to Table 2.
Bit 0 = 0 No time out.
= 1 Time out.

WDTR.0 will be set to one when WDT time out and can be reset to zero by:

Power On Reset, RESET pin, CLR WDT

Table 2 The bit 1 of WatchDog Timer Register (WDTR) reset item

RESET ITEM

WDTR.1 = 1

WDTR.1 = 0

Program Counter (PC)

0000H

Stack Pointer (SP)

Reset

ROMPR, PAGE, DBKR, WRP, ACC, CF, ZF,
SCR registers

Reset

IEF, HEF, SEF, HCF, PEF, EVF flags

IEF = Reset

Reset

DIV0, DIV1

Reset

TM0, TM1, MR0, MR1 registers

Reset

Timer 0 input clock

FOSC/4

Timer 1 input clock

FOSC

MFP output

Low

PM0 register

Reset

PM1, PM2, PM5 registers

Set (1111B)

PSR0 register

Reset

Input/output ports RA, RB, RD

Input mode

Output ports RE, RF

High

RA, RB ports output type

CMOS type

RC port pull-high resistors

Disable

Input clock of the watchdog timer

FOSC/2048

DTMF output

Hi-Z

BUZCR register

Reset

FLCD

Q5 to Q9 Reset

LCD display

OFF

LCDR

Reset

Segment output mode

LCD drive output

-: keep the status
Note: SCR.2 is reserved

Preliminary W742E81A/W742C81A

- 16 -

6.12 Timer/Counter

6.12.1 Timer 0 (TM0)

Timer 0 (TM0) is a programmable 8-bit binary down-counter. The specified value can be loaded into
TM0 by executing the MOV TM0L(TM0H),R instructions. When the MOV TM0L(TM0H),R instructions
are executed, it will stop the TM0 down-counting (if the TM0 is down-counting) and reset the MR0.3 to
0, and the specified value can be loaded into TM0. Then we can set MR0.3 to 1, that will cause the
event flag 1 (EVF.1) is reset and the TM0 starts to count. When it decreases and underflow to FFH,
Timer 0 stops operating and generates an underflow (EVF.1 = 1). Then, if the Timer 0 interrupt
enable flag has been set (IEF.1 = 1), the interrupt is executed, while if the hold release enable flag 1
has been set (HEF.1 = 1), the hold state is terminated. The Timer 0 clock input can be set as
F

OSC

/1024 or F

OSC

/4 by setting MR0.0 to 1 or resetting MR0.0 to 0. The default timer value is

OSC

/4. The organization of Timer 0 is shown in Figure 6-6.

If the Timer 0 clock input is F

OSC

/4:

Desired Timer 0 interval = (preset value +1)

1/F

OSC

If the Timer 0 clock input is F

OSC

/1024:

Desired Timer 0 interval = (preset value +1)

1024

1/F

OSC

Preset value: Decimal number of Timer 0 preset value

OSC

: Clock oscillation frequency

Fosc/4

Fosc/1024

Enable

Disable

1. Reset

2. CLR EVF,#02H

8-Bit Binary

Down Counter

S
R

HEF.1

IEF.1

Hold mode release (HCF.1)

Timer 0 interrupt (INT1)

1. Reset

2. CLR EVF,#02H

EVF.1

MR0.0

(Timer 0)

Set MR0.3 to 1

3. Reset MR0.3 to 0

3.Set MR0.3 to 1

MOV TM0H,R

MOV TM0L,R

4.MOV TM0L,R or MOV TM0H,R

Figure 6-6 Organization of Timer 0

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 17 - Revision A1

6.12.2 Timer 1 (TM1)

Timer 1 (TM1) is also a programmable 8-bit binary down counter, as shown in Figure 6-7. Timer 1
can be used as to output an arbitrary frequency to the MFP pin. The input clock of Timer 1 can be
one of three sources: F

OSC

/64, F

OSC

, or Fs. The source can be selected by setting bit 0 and bit 1 of

mode register 1 (MR1). At initial reset, the Timer 1 clock input is F

OSC

. When the MOV TM1L, R or

MOV TM1H,R instruction is executed, the specified data are loaded into the auto-reload buffer; but
the TM1 down-counting will keep going on. If the bit 3 of MR1 is set (MR1.3 = 1), the content of the
auto-reload buffer will be loaded into the TM1 down counter, and Timer 1 starts to down count, and
the event flag 7 is reset (EVF.7 = 0). When the timer decreases and underflow to FFH, it will generate
an underflow (EVF.7 = 1) and be auto-reloaded with the specified data, after which it will continue to
count down. Then, if interrupt enable flag 7 has been set to 1 (IEF.7 = 1), an interrupt is executed; if
hold mode release enable flag 7 is set to 1 (HEF.7 = 1), the hold state is terminated. The specified
frequency of Timer 1 can be delivered to the MFP output pin by programming bit 2 of MR1. Bit 3 of
MR1 can be used to make Timer 1 stop or start counting.

In a case where Timer 1 clock input is F

Desired Timer 1 interval = (preset value +1) / F

Desired frequency for MFP output pin = F

(preset value + 1)

2 (Hz)

Preset value: Decimal number of Timer 1 preset value

OSC

: Clock oscillation frequency

Auto-reload buffer

8 bits

MR1.3

Underflow signal

EVF.7

MFP

signal

BUZCR.0

output pin

8-Bit Binary

Down Counter

circuit

Reset

Disable

Enable

Fosc/64

Fosc

MR1.0

(Timer 1)

1. Reset

2. INT7 accept

3. CLR EVF, #80H

4. Set MR1.3 to 1

MOV TM1H,R

MOV TM1L,R

Set

MR1.3 to 1

MR1.1

MOV WR,TM1

8 bits

Figure 6-7 Organization of Timer 1

Preliminary W742E81A/W742C81A

- 18 -

For example, when F

equals 32768 Hz, depending on the preset value of TM1, the MFP pin will

output a single tone signal in the tone frequency range from 64 Hz to 16384 Hz. The relation between
the tone frequency and the preset value of TM1 is shown in the table below.

MOV WR,TM1 can read back the content of TM1, It will save the TM1 MSB to WR and the TM1 LSB
to ACC.

Table 3 The relation between the tone frequency and the present value of TM1

C
C

TM1 preset value
& MFP frequency

3rd octave

4th octave

5th octave

261.63

277.18

293.66

311.13

329.63

349.23

369.99

392.00

415.30

440.00

466.16

493.88

523.25

554.37

587.33

622.25

659.26

698.46

739.99

783.99

830.61

880.00

932.23

987.77

260.06

277.69

292.57

309.13

327.68

372.36

390.09

420.10

443.81

442.81

3EH

3AH

37H

34H

31H

2EH

2BH

29H

26H

22H

24H

20H

468.11

496.48

1EH

1CH

1BH

19H

18H

16H

15H

14H

13H

12H

11H

10H

528.51

564.96

585.14

630.15

655.36

712.34

744.72

780.19

819.20

862.84

910.22

963.76

130.81

138.59

146.83

155.56

164.81

174.61

185.00

196.00

207.65

220.00

233.08

246.94

7CH

75H

6FH

68H

62H

5DH

58H

53H

4EH

45H

49H

41H

131.07

138.84

146.28

156.03

165.49

174.30

184.09

195.04

207.39

221.40

234.05

248.24

Tone

frequency

Tone

frequency

TM1 preset value
& MFP frequency

Tone

frequency

TM1 preset value
& MFP frequency

Note: Central tone is A4 (440 Hz).

6.12.3 Mode Register 0 (MR0)

Mode Register 0 is organized as a 4-bit binary register (MR0.0 to MR0.3). MR0 can be used to control
the operation of Timer 0. The bit descriptions are as follows:

MR0

Note: W means write only.

Bit 0 = 0 The fundamental frequency of Timer 0 is F

OSC

/4.

= 1 The fundamental frequency of Timer 0 is F

OSC

/1024.

Bit 1 & Bit 2 are reserved

Bit 3 = 0 Timer 0 stops down-counting.

= 1 Timer 0 starts down-counting.

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 19 - Revision A1

6.12.4 Mode Register 1 (MR1) & MFP Control Pin (BUZCR)

Mode Register 1 is organized as a 4-bit binary register (MR1.0 to MR1.3). MR1 can be used to control
the operation of Timer 1. The bit descriptions are as follows:

MR1

Note: W means write only.

Bit 0 = 0 The internal fundamental frequency of Timer 1 is F

OSC

= 1 The internal fundamental frequency of Timer 1 is F

OSC

/64.

Bit 1 = 0 The fundamental frequency source of Timer 1 is the internal clock.

= 1 The fundamental frequency source of Timer 1 is the sub-oscillator frequency Fs (32768
Hz).

Bit 2 is reserved.

Bit 3 = 0 Timer 1 stops down-counting.

= 1 Timer 1 starts down-counting.

MFP control pin is organized as a 4-bit binary register.

BUZCR

Note: W means write only.

Bit 0 = 0 The specified waveform of the MFP generator is delivered to the MFP output pin.

= 1 The specified frequency of Timer 1 is delivered to the MFP output pin.

Bit 1, Bit 2 & Bit 3 are reserved.

6.13 Interrupts

The W742E81A/W742C81A provides four internal interrupt sources (Divider 0, Divider 1, Timer 0,
Timer 1) and one external interrupt source (port RC). Vector addresses for each of the interrupts are
located in the range of program memory (ROM) addresses 004H to 020H. The flags IEF, PEF, and
EVF are used to control the interrupts. When EVF is set to "1" by hardware and the corresponding bits
of IEF and PEF have been set by software, an interrupt is generated. When an interrupt occurs, all of
the interrupts are inhibited until the EN INT or MOV IEF,#I instruction is invoked. The interrupts can
also be disabled by executing the DIS INT instruction. When an interrupt is generated in hold mode,
the hold mode will be released momentarily and interrupt subroutine will be executed. After the RTN
instruction is executed in an interrupt subroutine, the

C will enter hold mode again. The operation

flow chart is shown in Figure 6-9. The control diagram is shown in Figure 6-9.

Preliminary W742E81A/W742C81A

- 20 -

IEF.0

IEF.1

Interrupt

Process

Circuit

Interrupt

Vector

Generator

004H

008H

020H

IEF.7

Initial Reset

CLR EVF,#I instruction

DIS INT instruction

Initial Reset

MOV IEF,#I

Enable

EN INT

EVF.1

EVF.0

EVF.7

Disable

Divider 0

overflow signal

Timer 0

underflow signal

Timer 1

underflow signal

IEF.2

EVF.2

RC port

IEF.4

EVF.4

overflow signal

signal change

00CH

Divider 1

014H

Figure 6-8 Interrupt event control diagram

6.14 Stop Mode Operation

In stop mode, all operations of the

C cease, and the MFP pin is kept to high. The

C enters stop

mode when the STOP instruction is executed and exits stop mode when an external trigger is
activated (by a falling signal on the RC). When the designated signal is accepted, the

C awakens

and executes the next instruction. To prevent erroneous execution, the NOP instruction should follow
the STOP command. But In the dual-clock slow operation mode, the STOP instruction will also
disable the sub-oscillator oscillating; all operations of the

C cease.

6.14.1 Stop Mode Wake-up Enable Flag for RC Port (SEF)

The stop mode wake-up flag for port RC is organized as an 4-bit binary register (SEF.0 to SEF.3).
Before port RC may be used to make the device exit the stop mode, the content of the SEF must be
set first. The SEF is controlled by the MOV SEF, #I instruction. The bit descriptions are as follows:

SEF

Note: W means write only.

SEF.0 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.0
SEF.1 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.1

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 21 - Revision A1

SEF.2 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.2
SEF.3 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.3

6.15 Hold Mode Operation

In hold mode, all operations of the

C cease, except for the operation of the oscillator, Timer, Divider,

LCD driver, DTMF generator and MFP generator. The

C enters hold mode when the HOLD

instruction is executed. The hold mode can be released in one of five ways: by the action of timer 0,
timer 1, divider 0, divider 1, the RC port. Before the device enters the hold mode, the HEF, PEF, and
IEF flags must be set to define the hold mode release conditions. For more details, refer to the
instruction-set table and the following flow chart.

Divider 0, Divider 1, Timer
0, Timer 1, Signal Change
at RC Port

HOLD
Mode?

IEF

Flag Set?

PC <- (PC+1)

IEF

Flag Set?

Yes

HOLD

HEF

Flag Set?

Reset EVF Flag

Execute

Interrupt Service Routine

Reset EVF Flag

Execute

Interrupt Service Routine

Interrupt

Enable?

Interrupt

Enable?

Yes

Disable interrupt

(Note)

Note: The bit of EVF corresponding to the interrupt signal will be reset.

Figure 6-9 Hold Mode and Interrupt Operation Flow Chart

Preliminary W742E81A/W742C81A

- 22 -

6.15.1 Hold Mode Release Enable Flag (HEF)

The hold mode release enable flag is organized as an 8-bit binary register (HEF.0 to HEF.7). The
HEF is used to control the hold mode release conditions. It is controlled by the MOV HEF, #I
instruction. The bit descriptions are as follows:

HEF

Note: W means write only.

HEF.0 = 1 Overflow from the Divider 0 causes Hold mode to be released.

HEF.1 = 1 Underflow from Timer 0 causes Hold mode to be released.

HEF.2 = 1 Signal change at port RC causes Hold mode to be released.

HEF.3, HEF.5 & HEF.6 are reserved.

HEF.4 = 1 Overflow from the Divider 1 causes Hold mode to be released.

HEF.7 = 1 Underflow from Timer 1 causes Hold mode to be released.

6.15.2 Interrupt Enable Flag (IEF)

The interrupt enable flag is organized as a 8-bit binary register (IEF.0 to IEF.7). These bits are used
to control the interrupt conditions. It is controlled by the MOV IEF, #I instruction. When one of these
interrupts is accepted, the corresponding to the bit of the event flag will be reset, but the other bits are
unaffected. In interrupt subroutine, these interrupts will be disable till the instruction MOV IEF, #I

EN INT

is executed again. Otherwise, these interrupts can be disable by executing DIS INT

instruction. The bit descriptions are as follows:

IEF

Note: W means write only.

IEF.0 = 1 Interrupt 0 is accepted by overflow from the Divider 0.

IEF.1 = 1 Interrupt 1 is accepted by underflow from the Timer 0.
IEF.2 = 1 Interrupt 2 is accepted by a signal change at port RC.

IEF.3, IEF.5 & IEF.6 are reserved.
IEF.4 = 1 Interrupt 4 is accepted by overflow from the Divider 1.

IEF.7 = 1 Interrupt 7 is accepted by underflow from Timer 1.

6.15.3 Port Enable Flag (PEF)

The port enable flag is organized as 4-bit binary register (PEF.0 to PEF.3). Before port RC may be
used to release the hold mode or preform interrupt function, the content of the PEF must be set first.
The PEF is controlled by the MOV PEF, #I instruction. The bit descriptions are as follows:

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 23 - Revision A1

PEF

Note: W means write only.

PEF.0: Enable/disable the signal change at pin RC.0 to release hold mode or perform interrupt.

PEF.1: Enable/disable the signal change at pin RC.1 to release hold mode or perform interrupt.
PEF.2: Enable/disable the signal change at pin RC.2 to release hold mode or perform interrupt.

PEF.3: Enable/disable the signal change at pin RC.3 to release hold mode or perform interrupt.

6.15.4 Hold Mode Release Condition Flag (HCF)

The hold mode release condition flag is organized as a 8-bit binary register (HCF.0 to HCF.7). It
indicates by which interrupt source the hold mode has been released, and is loaded by hardware. The
HCF can be read out by the MOVA R, HCFL

and MOVA R, HCFH instructions. When any of the HCF

bits is "1," the hold mode will be released and the HOLD instruction is invalid. The HCF can be reset
by the CLR EVF or MOV HEF,#I (HEF = 0) instructions. When EVF and HEF have been reset, the
corresponding bit of HCF is reset simultaneously. The bit descriptions are as follows:

HCF

Note: R means read only.

HCF.0 = 1 Hold mode was released by overflow from the divider 0.

HCF.1 = 1 Hold mode was released by underflow from the timer 0.

HCF.2 = 1 Hold mode was released by a signal change at port RC.

HCF.3 is reserved.

HCF.4 = 1 Hold mode was released by overflow from the divider 1.

HCF.5 = 1 Hold mode was released by underflow from the timer 1.

HCF.6 and HCF.7 are reserved.

6.15.5 Event Flag (EVF)

The event flag is organized as a 8-bit binary register (EVF.0 to EVF.7). It is set by hardware and reset
by CLR EVF,#I instruction or the occurrence of an interrupt. The bit descriptions are as follows:

EVF

Note: R means read only.

Preliminary W742E81A/W742C81A

- 24 -

EVF.0 = 1 Overflow from divider 0 occurred.

EVF.1 = 1 Underflow from timer 0 occurred.

EVF.2 = 1 Signal change at port RC occurred.

EVF.3 is reserved.

EVF.4 = 1 Overflow from divider 1 occurred.

EVF.5 & EVF.6 are reserved.

EVF.7 = 1 Underflow from Timer 1 occurred.

6.16 Reset Function

The W742E81A/W742C81A is reset either by a power-on reset or by using the external RES pin.
The initial state of the W742E81A/W742C81A after the reset function is executed is described below.

Table 4 The initial state after the reset function is executed

Program Counter (PC)

000H

WDTR registers

Reset

BUZCR registers

Reset

ACC, CF, ZF registers

Reset

MR0, MR1, PAGE registers

Reset

PSR0, SCR, TM0, TM1 registers

Reset

IEF, HEF, HCF, PEF, EVF, SEF flags

Reset

WRP, DBKR, PAGE registers

Reset

Timer 0 input clock

OSC

Timer 1 input clock

OSC

MFP output

Low

DTMF output

Hi-Z

Input/output ports RA, RB, RD

Input mode

Output port RE & RF

High

RA, RB ports output type

CMOS type

RC ports pull-high resistors

Disable

Input clock of the watchdog timer

OSC

/2048

LCD display

OFF

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 25 - Revision A1

6.17 Input/Output Ports RA, RB & RD

Port RA consists of pins RA.0 to RA.3. Port RB consists of pins RB.0 to RB.3. Port RD consists of
pins RD.0 to RD.3. At initial reset, input/output ports RA, RB and RD are all in input mode. When
RA, RB are used as output ports, CMOS or NMOS open drain output type can be selected by the
PM0 register. But when RD is used as output port, the output type is just fixed to be CMOS output
type. Each pin of port RA, RB and RD can be specified as input or output mode independently by the
PM1, PM2 and PM5 registers. The MOVA R, RA or MOVA R, RB or MOVA R, RD instructions
operate the input functions and the MOV RA, R or MOV RB, R or MOV RD, R operate the output
functions. For more details, refer to the instruction table and Figure 6-10 and Figure 6-11.

Input/Output Pin of the RA(RB)

I/O PIN

RA.n(RB.n)

DATA

BUS

Buffer

Output

PM0.0(PM0.1)

PM1.n (PM2.n)

MOVA R,RA(MOVA R,RB) instruction

MOV RA,R(MOV RB,R)

instruction

Enable

Figure 6-10 Architecture of RA (RB) Input/Output Pins

Input/Output Pin of the RD

I/O PIN

RD.n

DATA

BUS

Buffer

Output

PM5.n

MOVA R,RD instruction

MOV RD,R instruction

Enable

Figure 6-11 Architecture of RD Input/Output pins

6.17.1 Port Mode 0 Register (PM0)

The port mode 0 register is organized as 4-bit binary register (PM0.0 to PM0.3). PM0 can be used to

Preliminary W742E81A/W742C81A

- 26 -

determine the structure of the input/output ports; it is controlled by the MOV PM0, #I instruction. The
bit descriptions are as follows:

PM0

Note: W means write only.

Bit 0 = 0 RA port is CMOS output type. Bit 0 = 1 RA port is NMOS open drain output type.

Bit 1 = 0 RB port is CMOS output type. Bit 1 = 1 RB port is NMOS open drain output type.

Bit 2 = 0 RC port pull-high resistor is disabled. Bit 2 = 1 RC port pull-high resistor is enabled.

Bit 3 is reserved.

6.17.2 Port Mode 1 Register (PM1)

The port mode 1 register is organized as 4-bit binary register (PM1.0 to PM1.3). PM1 can be used to
control the input/output mode of port RA. PM1 is controlled by the MOV PM1, #I instruction. The bit
descriptions are as follows:

PM1

Note: W means write only.

Bit 0 = 0 RA.0 works as output pin; Bit 0 = 1 RA.0 works as input pin
Bit 1 = 0 RA.1 works as output pin; Bit 1 = 1 RA.1 works as input pin
Bit 2 = 0 RA.2 works as output pin; Bit 2 = 1 RA.2 works as input pin

Bit 3 = 0 RA.3 works as output pin; Bit 3 = 1 RA.3 works as input pin
At initial reset, port RA is input mode (PM1 = 1111B).

6.17.3 Port Mode 2 Register (PM2)

The port mode 2 register is organized as 4-bit binary register (PM2.0 to PM2.3). PM2 can be used to
control the input/output mode of port RB. PM2 is controlled by the MOV PM2, #I instruction. The bit
descriptions are as follows:

PM2

Note: W means write only.

Bit 0 = 0 RB.0 works as output pin; Bit 0 = 1 RB.0 works as input pin
Bit 1 = 0 RB.1 works as output pin; Bit 1 = 1 RB.1 works as input pin
Bit 2 = 0 RB.2 works as output pin; Bit 2 = 1 RB.2 works as input pin

Bit 3 = 0 RB.3 works as output pin; Bit 3 = 1 RB.3 works as input pin
At initial reset, the port RB is input mode (PM2 = 1111B).

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 27 - Revision A1

6.17.4 Port Mode 5 Register (PM5)

The port mode 5 register is organized as 4-bit binary register (PM5.0 to PM5.3). PM5 can be used to
control the input/output mode of port RD. PM5 is controlled by the MOV PM5, #I instruction. The bit
descriptions are as follows:

PM5

Note: W means write only.

Bit 0 = 0 RD.0 works as output pin; Bit 0 = 1 RD.0 works as input pin

Bit 1 = 0 RD.1 works as output pin; Bit 1 = 1 RD.1 works as input pin
Bit 2 = 0 RD.2 works as output pin; Bit 2 = 1 RD.2 works as input pin

Bit 3 = 0 RD.3 works as output pin; Bit 3 = 1 RD.3 works as input pin
At initial reset, the port RD is input mode (PM5 = 1111B).

6.18 Input Ports RC

Port RC consists of pins RC.0 to RC.3. Each pin of port RC can be connected to a pull-up resistor,
which is controlled by the port mode 0 register (PM0). When the PEF, HEF, and IEF corresponding to
the RC port are set, a signal change at the specified pins of port RC will execute the hold mode
release or interrupt subroutine. Port status register 0 (PSR0) records the status of ports RC, i.e., any
signal changes on the pins that make up the ports. PSR0 can be read out and cleared by the MOV R,
PSR0, and CLR PSR0 instructions. In addition, the falling edge signal on the pin of port RC specified
by the instruction MOV SEF, #I will cause the device to exit the stop mode

. Refer to Figure 6-12

and the instruction table for more details.

Preliminary W742E81A/W742C81A

- 28 -

Signal

change

detector

PEF.0

PSR0.0

PSR0.2

DATA BUS

RC.0

PSR0.3

PEF.3

Reset

CLR PSR0

HCF.2

INT 2

Reset

CLR EVF, #I

EVF.2

HEF.2

IEF.2

Falling

Edge

detector

Falling

Edge

detector

Falling

Edge

detector

Falling

Edge

detector

SEF.0

SEF.1

SEF.2

SEF.3

To Wake Up Stop Mode

Signal

change

detector

PSR0.1

RC.1

PEF.1

Signal

change

detector

PEF.2

RC.2

Signal

change

detector

RC.3

PM0.2

MOV PEF, #I

Figure 6-12 Architecture of Input Ports RC

6.18.1 Port Status Register 0 (PSR0)

Port status register 0 is organized as 4-bit binary register (PSR0.0 to PSR0.3). PSR0 can be read or
cleared by the MOVA R, PSR0, and CLR PSR0 instructions. The bit descriptions are as follows:

PSR0

Note: R means read only.

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 29 - Revision A1

Bit 0 = 1 Signal change at RC.0
Bit 1 = 1 Signal change at RC.1

Bit 2 = 1 Signal change at RC.2
Bit 3 = 1 Signal change at RC.3

6.19 Output Port RE & RF

Output port RE is used as an output of the internal RT port. When the MOV RE, R instruction is
executed, the data in the RAM will be output to port RT through port RE. It provides a high sink
current to drive an LED. RF port is just used as a output port. When the MOV RF, R instruction is
executed, the data in the RAM will be output to RF.

6.20 DTMF Output Pin (DTMF)

This pin should output the dual tone multi-frequency signal from the DTMF generator. There is the
DTMF register that can specify the wanted low/high frequency. And control whether the dual tone will
be output or not. The tones are divided into two groups (Row group and Col group) and one tone from
each group is selected to represent a digit. The relation between the DTMF signal and the
corresponding touch tone keypad is shown in Figure 6-13.

Row/Col

Frequency

697 Hz

770 Hz

852 Hz

941 Hz

1209 Hz

1336 Hz

1477 Hz

1633 Hz

Figure 6-13 The relation between the touch tone keypad and the frequency

6.20.1 DTMF register

DTMF register is organized as 4-bit binary register. By controlling the DTMF register, one tone of the
low/high group can be selected. The MOV DTMF,R instruction can specify the wanted tones. The bit
descriptions are as follows:

DTMF

Note: W means write only.

Preliminary W742E81A/W742C81A

- 30 -

SELECTED TONE

1209 Hz

High

1336 Hz

Group

1477 Hz

1633 Hz

697 Hz

Low

770 Hz

Group

852 Hz

941 Hz

Note: X means this bit do not care.

6.20.2 Dual Tone Control Register (DTCR)

Dual tone control register is organized as 4-bit binary register. The output of the dual or single tone
will be controlled by this register. The MOV DTCR,#I instruction can specify the wanted status. The bit
descriptions are as follows:

DTCR

Note: W means write only.

Bit 0 = 1 Low group tone output is enabled.

Bit 1 = 1 High group tone output is enabled.
Bit 2 = 1 DTMF output is enabled. When Bit 2 is reset to 0, the DTMF output pin will be Hi-Z
state.

Bit 3 is reserved.

6.21 MFP Output Pin (MFP)

The MFP output pin can output the Timer 1 clock or the modulation frequency; the output of the pin is
determined by bit 0 of BUZCR (BUZCR.0). The organization of MR1 is shown in Figure 6-7. When
bit 0 of BUZCR is reset to "0," the MFP output can deliver a modulation output in any combination of
one signal from among DC, 4096 Hz, 2048 Hz, and one or more signals from among 128 Hz, 64 Hz,
8 Hz, 4 Hz, 2 Hz, or 1 Hz (when using a 32.768 KHz crystal). The MOV MFP, #I instruction is used to
specify the modulation output combination. The data specified by the 8-bit operand and the MFP
output pin are shown in next page.

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 31 - Revision A1

Table 5 The relation between the MFP output frequncy and the data specified by 8-bit operand

(Fosc = 32.768 KHz)

R7 R6

FUNCTION

Low level

128 Hz

64 Hz

0 0

8 Hz

4 Hz

2 Hz

1 Hz

High level

128 Hz

64 Hz

0 1

8 Hz

4 Hz

2 Hz

1 Hz

2048 Hz

2048 Hz * 128 Hz

2048 Hz * 64 Hz

1 0

2048 Hz * 8 Hz

2048 Hz * 4 Hz

2048 Hz * 2 Hz

2048 Hz * 1 Hz

4096 Hz

4096 Hz * 128 Hz

4096 Hz * 64 Hz

1 1

4096 Hz * 8 Hz

4096 Hz * 4 Hz

4096 Hz * 2 Hz

4096 Hz * 1 Hz

Preliminary W742E81A/W742C81A

- 32 -

6.22 LCD Controller/Driver

The W742E81A/W742C81A can directly drive an LCD with 40 segment output pins and 4 common
output pins for a total of 40

4 dots. The LCD driving mode is 1/3 bias 1/4 duty. The alternating

frequency of the LCD can be set as Fw/64, Fw/128, Fw/256, or Fw/512. The structure of the LCD
alternating frequency (F

LCD

) is shown in the Figure 6-14.

Selector

Fw/512

Fw/256

Fw/128

Fw/64

Fs or Fosc/128

(By Dual or single

clock Option)

LCD

Figure 6-14 LCD alternating frequency (FLCD) circuit diagram

Fw = 32.768 KHz, the LCD frequency is as shown in the table below.

Table 6 The relationship between the FLCD and the duty cycle

LCD FREQUENCY

Fw/64 (512Hz)

Fw/128 (256Hz)

Fw/256 (128Hz)

Fw/512 (64Hz)

1/4 DUTY

128 Hz

64 Hz

32 Hz

16 Hz

Corresponding to the 40 LCD drive output pins, there are 40 LCD data RAM segments. Instructions
such as MOV LPL,R, MOV LPH,R, MOV @LP,R, and MOV R,@LP are used to control the LCD data
RAM. The data in the LCD data RAM are transferred to the segment output pins automatically without
program control. When the bit value of the LCD data RAM is "1," the LCD is turned on. When the bit
value of the LCD data RAM is "0," LCD is turned off. The contents of the LCD data RAM (LCDR) are
sent out through the segment0 to segment39 pins by a direct memory access. The relation between
the LCD data RAM and segment/common pins is shown below.

Table 7 The reation between the LCDR and segment/common pins used as LCD drive output pins

COM3

COM2 COM1 COM0

LCD DATA RAM

OUTPUT PIN

BIT 3

BIT 2

BIT 1

BIT 0

LCDR00

SEG0

0/1

LCDR01

SEG1

0/1

LCDR26

SEG38

0/1

LCDR27

SEG39

0/1

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 33 - Revision A1

The LCDON instruction turns the LCD display on (even in HOLD mode), and the LCDOFF instruction
turns the LCD display off. At initial reset, all the LCD segments are unlit. When the initial reset state
ends, the LCD display is turned off automatically. To turn on the LCD display, the instruction LCDON
must be executed.

6.22.1 LCD RAM addressing method

There are 40 LCD RAMs (LCDR00 - LCDR27) that should be indirectly addressed. The LCD RAM
pointer (LP) is used to point to the address of the wanted LCD RAM. The LP is organized as 6-bit
binary register. The MOV LPL,R and MOV LPH,R instructions can load the LCD RAM address to the
LP from R. The MOV @LP,R and MOV R,@LP instructions can access the pointed LCD RAM
content.

6.22.2 The output waveforms for the LCD driving mode

1/3 bias 1/4 duty Lighting System (Example)

Normal Operating Mode

COM0

VDD2
VDD1
VSS

VDD3

VDD2
VDD1
VSS

VDD3

COM1

COM2

VDD2
VDD1
VSS

VDD3

VDD2
VDD1
VSS

VDD3

COM3

VDD2
VDD1
VSS

VDD3

VDD2
VDD1
VSS

VDD3

LCD driver
outputs for
only seg. on
COM0 side
being lit

LCD driver
outputs for
only seg. on
COM1 side
being lit

Preliminary W742E81A/W742C81A

- 34 -

Continued

VDD2
VDD1
VSS

VDD3

VDD2
VDD1
VSS

VDD3

LCD driver
outputs for
seg. on COM0,
COM1 sides
being lit

LCD driver
outputs for
seg. on COM1,
COM2,3 sides
being lit

VDD2
VDD1
VSS

VDD3

VDD2
VDD1
VSS

VDD3

LCD driver
outputs for
seg. on COM1
COM2 sides
being lit

LCD driver
outputs for
seg. on COM0
COM2,3 sides
being lit

VDD2
VDD1
VSS

VDD3

LCD driver
outputs for
seg. on COM0
COM1,2,3 sides
being lit

The power connections for the 1/3 bias 1/4 duty LCD driving mode are shown below.

DH1

DH2

VSS

VDD1

VDD

VDD2

0.1uF

VDD = 3.0 V

C
H
I
P

1/3 Bias at VDD = 3.0 V

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 35 - Revision A1

6.23 Mode Description

The built-in program code memory of the

W742E81A/W742C81A

is the EEPROM structure. This

memory can be programmed, erased and verified through the VPP, MODE and DATA pins.

7. ABSOLUTE MAXIMUM RATINGS

PARAMETER

RATING

UNIT

Supply Voltage to Ground Potential

-0.3 to +7.0

Applied Input/Output Voltage

-0.3 to +7.0

Power Dissipation

120

Ambient Operating Temperature

0 to +70

Storage Temperature

-55 to +150

Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability

of the device.

8. DC CHARACTERISTICS

-V

= 3.0 V, Fm = 3.58 MHz, Fs = 32.768 KHz, T

= 25

C, LCD on; unless otherwise specified)

PARAMETER

SYM.

CONDITIONS

MIN. TYP. MAX. UNIT

Op. Voltage

2.4

3.8

Op. Current (Crystal type)

OP1

No load (Ext-V)

In dual-clock normal

operation

0.9

2.5

Op. Current (Crystal type)

OP3

No load (Ext-V)

In dual-clock slow operation

and Fm is stopped

Hold Current (Crystal type)

HM1

Hold mode No load (Ext-V)

In dual-clock normal

operation

450

Hold Current (Crystal type)

HM3

Hold mode No load (Ext-V)

In dual-clock slow operation

and Fm is stopped

Stop Current (Crystal type)

SM1

Stop mode No load (Ext-V)

In dual-clock normal

operation

Preliminary W742E81A/W742C81A

- 36 -

DC Characteristics, continued

PARAMETER

SYM.

CONDITIONS

MIN. TYP. MAX. UNIT

Input Low Voltage

0.3

Input High Voltage

0.7

MFP Output Low Voltage

= 3.5 mA

0.4

MFP Output High Voltage

= 3.5 mA

2.4

Port RA, RB, RD and RF
Output Low Voltage

ABL

= 2.0 mA

0.4

Port RA, RB, RD and RF
Output high Voltage

ABH

= 2.0 mA

2.4

LCD Supply Current

LCD

All Seg. ON

SEG0-SEG39 Sink
Current (Used as LCD
output)

OL1

= 0.4V

LCD

= 0.0V

SEG0-SEG39 Drive
Current
(Used as LCD output)

OH1

= 2.4V

LCD

= 3.0V

Port RE Sink Current

= 0.9V

Port RE Source Current

= 2.4V

0.4

1.2

DTMF Output DC level

TDC

= 5 K

= 2.5 to 3.8V

1.1

2.8

DTMF Distortion

= 5 K

= 2.5 to 3.8V

-30

-23

DTMF Output Voltage

Low group,

= 5 K

130

150

170

mVrms

Pre-emphasis

Col/Row

DTMF Output Sink Current

= 0.5V

0.2

Pull-up Resistor

Port RC

100

350

1000

RES Pull-up Resistor

RES

100

500

9. AC CHARACTERISTICS

PARAMETER

SYM.

CONDITIONS

MIN.

TYP.

MAX. UNIT

Op. Frequency

OSC

Crystal type

3.58

MHz

Instruction Cycle time

One machine cycle

4/F

OSC

Reset Active Width

RAW

OSC

= 32.768 KHz

Interrupt Active Width

IAW

OSC

= 32.768 KHz

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 37 - Revision A1

10. INSTRUCTION SET TABLE

Symbol Description

ACC:

Accumulator

ACC.n:

Accumulator bit n

WR:

Working Register

WRP:

WR Page Register

PAGE:

Page Register

DBKR:

Data Bank Register

ROMPR:

ROM Page Register

MR0:

Mode Register 0

MR1:

Mode Register 1

PM0:

Port Mode 0

PM1:

Port Mode 1

PM2:

Port Mode 2

PM5:

Port Mode 5

PSR0:

Port Status Register 0

Memory (RAM) of address R

WDTR:

WatchDog Timer Register

LPL:

LCD data RAM pointer

LPH:

LCD data RAM pointer

R.n:

Memory bit n of address R

SCR: System Control Register

BUZCR:

Buzzer Control Register

RA:

I/O Port RA

RC:

I/O Port RC

DTMF:

DTMF Register

DTCR:

MTMF Control Pin

MFP:

MFP Output Pin

Preliminary W742E81A/W742C81A

- 38 -

Symbol Description, continued

Constant parameter

Branch or Jump address

CF:

Carry Flag

ZF:

Zero Flag

PC:

Program Counter

TM0L:

Low nibble of the Timer 0 counter

TM0H:

High nibble of the Timer 0 counter

TM1L:

Low nibble of the Timer 1 counter

TM1H:

High nibble of the Timer 1 counter

TAB0:

Look-up table address buffer 0

TAB1:

Look-up table address buffer 1

TAB2:

Look-up table address buffer 2

TAB3:

Look-up table address buffer 3

IEF.n:

Interrupt Enable Flag n

HCF.n:

HOLD mode release Condition Flag n

HEF.n:

HOLD mode release Enable Flag n

SEF.n:

STOP mode wake-up Enable Flag n

PEF.n:

Port Enable Flag n

EVF.n:

Event Flag n

! =:

Not equal

AND

EX:

Exclusive OR

Transfer direction, result

[PAGE*10H+()]:

Contents of address PAGE (bit2, bit1, bit0)*10H+()

[P()]:

Contents of port P

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 39 - Revision A1

Machine code

Mnemonic

Function

Flag affected

W/C

Arithmetic

0001 1000 0xxx xxxx

ADD

R, ACC

ACC

(R) + (ACC)

ZF, CF

1/1

0001 1100 i i i i nnnn

ADD

WRn, #I

ACC

(WRn) + I

ZF, CF

1/1

0001 1001 0xxx xxxx

ADDR

R, ACC

ACC, R

(R) + (ACC)

ZF, CF

1/1

0001 1101 i i i i nnnn

ADDR

WRn, #I

ACC, WRn

(WRn) + I

ZF, CF

1/1

0000 1000 0xxx xxxx

ADC

R, ACC

ACC

(R) + (ACC) + (CF)

ZF, CF

1/1

0000 1100 i i i i nnnn

ADC

WRn, #I

ACC

(WRn) + I + (CF)

ZF, CF

1/1

0000 1001 0xxx xxxx

ADCR

R, ACC

ACC, R

(R) + (ACC) + (CF)

ZF, CF

1/1

0000 1101 i i i i nnnn

ADCR

WRn, #I

ACC, WRn

(WRn) + I + (CF)

ZF, CF

1/1

0010 1000 0xxx xxxx

ADU

R, ACC

ACC

(R) + (ACC)

1/1

0010 1100 i i i i nnnn

ADU

WRn, #I

ACC

(WRn) + I

1/1

0010 1001 0xxx xxxx

ADUR

R, ACC

ACC, R

(R) + (ACC)

1/1

0010 1101 i i i i nnnn

ADUR

WRn, #I

ACC, WRn

(WRn) + I

1/1

0001 1010 0xxx xxxx

SUB

R, ACC

ACC

(R) - (ACC)

ZF, CF

1/1

0001 1110 i i i i nnnn

SUB

WRn, #I

ACC

(WRn) - I

ZF, CF

1/1

0001 1011 0xxx xxxx

SUBR

R, ACC

ACC, R

(R) - (ACC)

ZF, CF

1/1

0001 1111 i i i i nnnn

SUBR

WRn, #I

ACC, WR

(WR) - I

ZF, CF

1/1

0000 1010 0xxx xxxx

SBC

R, ACC

ACC

(R) - (ACC) - (CF)

ZF, CF

1/1

0000 1110 i i i i nnnn

SBC

WRn, #I

ACC

(WRn) - I - (CF)

ZF, CF

1/1

0000 1011 0xxxxxxx

SBCR

R, ACC

ACC, R

(R) - (ACC) - (CF)

ZF, CF

1/1

0000 1111 i i i i nnnn

SBCR

WRn, #I

ACC, WRn

(WRn) - I - (CF)

ZF, CF

1/1

0100 1010 0xxx xxxx

INC

ACC, R

(R) + 1

ZF, CF

1/1

0100 1010 1xxx xxxx

DEC

ACC, R

(R) - 1

ZF, CF

1/1

Preliminary W742E81A/W742C81A

- 40 -

Instruction set, continued

Machine code

Mnemonic

Function

Flag affected

W/C

Logic

0010 1010 0xxx xxxx

ANL

R, ACC

ACC

(R) & (ACC)

1/1

0010 1110 i i i i nnnn

ANL

WRn, #I

ACC

(WRn) & I

1/1

0010 1011 0xxx xxxx

ANLR

R, ACC

ACC, R

(R) & (ACC)

1/1

0010 1111 i i i i nnnn

ANLR

WRn, #I

ACC, WRn

(WRn) & I

1/1

0011 1010 0xxx xxxx

ORL

R, ACC

ACC

(R)

(ACC)

1/1

0011 1110 i i i i nnnn

ORL

WRn, #I

ACC

(WRn)

1/1

0011 1011 0xxx xxxx

ORLR

R, ACC

ACC, R

(R)

(ACC)

1/1

0011 1111 i i i i nnnn

ORLR

WRn, #I

ACC, WRn

(WRn)

1/1

0011 1000 0xxx xxxx

XRL

R, ACC

ACC

(R) EX (ACC)

1/1

0011 1100 i i i i nnnn

XRL

WRn, #I

ACC

(WRn) EX I

1/1

0011 1001 0xxx xxxx

XRLR

R, ACC

ACC, R

(R) EX (ACC)

1/1

0011 1101 i i i i nnnn

XRLR

WRn, #I

ACC, WRn

(WRn) EX I

1/1

Branch

0111 0

aaa aaaa aaaa

JMP

PC12~PC0

(ROMPR)

800H+L10~L0

1/1

1000 0

aaa aaaa aaaa

JB0

PC10~PC0

L10~L0; if ACC.0 = "1"

1/1

1001 0

aaa aaaa aaaa

JB1

PC10~PC0

L10~L0; if ACC.1 = "1"

1/1

1010 0

aaa aaaa aaaa

JB2

PC10~PC0

L10~L0; if ACC.2 = "1"

1/1

1011 0

aaa aaaa aaaa

JB3

PC10~PC0

L10~L0; if ACC.3 = "1"

1/1

1110 0

aaa aaaa aaaa

PC10~PC0

L10~L0; if ACC = 0

1/1

1100 0

aaa aaaa aaaa

JNZ

PC10~PC0

L10~L0; if ACC ! = 0

1/1

1111 0

aaa aaaa aaaa

PC10~PC0

L10~L0; if CF = "1"

1/1

1101 0

aaa aaaa aaaa

JNC

PC10~PC0

L10~L0; if CF != "1"

1/1

0100 1000 0xxx xxxx

DSKZ

ACC, R

(R) - 1; PC

(PC) + 2 if ACC =

ZF, CF

1/1

0100 1000 1xxx xxxx

DSKNZ

ACC, R

(R) - 1; PC

(PC) + 2 if ACC !=

ZF, CF

1/1

1010 1000 0xxx xxxx

SKB0

(PC) + 2 if R.0 = "1"

1/1

1010 1000 1xxx xxxx

SKB1

(PC) + 2 if R.1 = "1"

1/1

1010 1001 0xxx xxxx

SKB2

(PC) + 2 if R.2 = "1"

1/1

1010 1001 1xxx xxxx

SKB3

(PC) + 2 if R.3 = "1"

1/1

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 41 - Revision A1

Instruction set, continued

Machine code

Mnemonic

Function

Flag affected

W/C

Data move

0001 0000 0000 iiii

MOV

ACC, #I

ACC

1/1

1110 1nnn nxxx xxxx

MOV

WRn, R

WRn

(R)

1/1

1001 1001 iiii nnnn

MOV

WRn, #I

WRn

1/1

1111 1nnn nxxx xxxx

MOV

R, WRn

(WRn)

1/1

0110 1nnn nxxx xxxx

MOVA

WRn, R

ACC, WRn

(R)

1/1

0111 1nnn nxxx xxxx

MOVA

R, WRn

ACC, R

(WRn)

1/1

0101 1001 1xxx xxxx

MOV

R, ACC

(ACC)

1/1

0100 1110 1xxx xxxx

MOV

ACC, R

ACC

(R)

1/1

1011 1i i i i xxx xxxx

MOV

R, #I

1/1

1100 1nnn n000 qqqq

MOV

WRn, @WRq

WRn

[(DBKR)

80H+(PAGE)x10H +(WRq)]

1/2

1101 1nnn n000 qqqq

MOV

@WRq, WRn

[(DBKR)

80H+(PAGE)x10H +(WRq)]

WRn

1/2

1000 1100 0xxx xxxx

MOV

TAB0, R

TAB0

(R)

1/1

1000 1100 1xxx xxxx

MOV

TAB1, R

TAB1

(R)

1/1

1000 1110 0xxx xxxx

MOV

TAB2, R

TAB2

(R)

1/1

1000 1110 1xxx xxxx

MOV

TAB3, R

TAB3

(R)

1/1

1000 1101 0xxx xxxx

MOVC

[(TAB3)

1000H+(TAB2)x100H+(TAB1)

x10H + (TAB0)]

1/2

Input & Output

0101 1011 0xxx xxxx

MOVA

R, RA

ACC, R

[RA]

1/1

0101 1011 1xxx xxxx

MOVA

R, RB

ACC, R

[RB]

1/1

0100 1011 0xxx xxxx

MOVA

R, RC

ACC, R

[RC]

1/1

0100 1011 1xxx xxxx

MOVA

R, RD

ACC, R

[RD]

1/1

0101 1010 0xxx xxxx

MOV

RA, R

[RA]

(R)

1/1

0101 1010 1xxx xxxx

MOV

RB, R

[RB]

(R)

1/1

0100 1010 0xxx xxxx

MOV

RC, R

[RC]

(R)

1/1

1010 1100 1xxx xxxx

MOV

RD, R

[RD]

(R)

1/1

0101 1110 0xxx xxxx

MOV

RE, R

[RE]

(R)

1/1

1010 1110 0xxx xxxx

MOV

RF, R

[RF]

(R)

1/1

Preliminary W742E81A/W742C81A

- 42 -

Instruction set, continued

Machine code

Mnemonic

Function

Flag affected

W/C

Flag & Register

0101 1111 1xxx xxxx

MOVA

R, PAGE

ACC, R

PAGE (Page Register)

1/1

0101 1110 1xxx xxxx

MOV

PAGE, R

PAGE

(R)

1/1

0101 0110 1000 0i i i

MOV

PAGE, #I

PAGE

1/1

1001 1101 1xxx xxxx

MOV

R, WRP

WRP

1/1

1001 1100 1xxx xxxx

MOV

WRP, R

WRP

(R)

1/1

0011 0101 1000 i i i i

MOV

WRP, #I

WRP

1/1

1001 1101 0000 nnnn

MOV

WRn,DBKR

WRn

DBKR

1/1

1001 1111 0000 nnnn

MOV

WRn,TM1

WRn

TM1.4 - TM1.7, ACC

TM1.0 -

TM1.3

1/1

1001 1100 0000 nnnn

MOV

DBKR, WRn

DBKR

WRn

1/1

0011 0101 0000 ii i i

MOV

DBKR, #I

DBKR

1/1

0011 0100 0000 0ii i

MOV

ROMPR, #I

ROMPR

1/1

1000 1000 0xxx xxxx

MOV

ROMPR, R

ROMPR

(R)

1/1

1000 1001 0xxx xxxx

MOV

R, ROMPR

(ROMPR)

1/1

0101 1001 0xxx xxxx

MOVA

R, CF

ACC.0, R.0

1/1

0101 1000 0xxx xxxx

MOV

CF, R

(R.0)

1/1

0100 1001 0xxx xxxx

MOVA

R, HCFL

ACC, R

HCF.0~HCF.3

1/1

0100 1001 1xxx xxxx

MOVA

R, HCFH

ACC, R

HCF.4~HCF.7

1/1

0101 0011 0000 i i i i

MOV

PM0, #I

Port Mode 0

1/1

0101 0111 0000 i i i i

MOV

PM1, #I

Port Mode 1

1/1

0101 0111 1000 i i i i

MOV

PM2, #I

Port Mode 2

1/1

0011 0111 1000 i i i i

MOV

PM5, #I

Port Mode 5

1/1

0100 0000 i00i 0i i i

CLR

EVF, #I

Clear Event Flag if In = 1

1/1

0101 1101 0xxx xxxx

MOVA

R, EVFL

EVF.0 - EVF.3

1/1

0101 1101 1xxx xxxx

MOVA

R, EVFH

EVF.4 - EVF.7

1/1

0100 0001 i00i 0i i i

MOV

HEF, #I

Set/Reset HOLD mode release Enable Flag

1/1

0101 0001 i00i 0i i i

MOV

IEF, #I

Set/Reset Interrupt Enable Flag

1/1

0100 0011 0000 i i i i

MOV

PEF, #I

Set/Reset Port Enable Flag

1/1

0101 0010 0000 i i i i

MOV

SEF, #I

Set/Reset STOP mode wake-up Enable Flag
for RC port

1/1

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 43 - Revision A1

Instruction set, continued

Machine code

Mnemonic

Function

Flag affected

W/C

Flag & Register

0101 0100 0000 i 0 i i

MOV

SCR, #I

SCR

1/1

0100 1111 0xxx xxxx

MOVA

R, PSR0

ACC, R

Port Status Register 0

1/1

0100 0010 0000 0000

CLR

PSR0

Clear Port Status Register 0

1/1

0101 0000 0100 0000

SET

Set Carry Flag

1/1

0101 0000 0000 0000

CLR

Clear Carry Flag

1/1

0001 0111 0000 0000

CLR

DIVR0

Clear the last 4-bit of the Divider 0

1/1

0101 0101 1000 0000

CLR

DIVR1

Clear the last 4-bit of the Divider 1

1/1

0101 0110 0000 i i i i

MOV

WDTR, #I

WDTR

1/1

0101 1111 0xxx xxxx

MOVA

R,WDTR

ACC, R

Watchdog Timer Register

1/1

0001 0111 1000 0000

CLR

WDT

Clear Watchdog Timer

1/1

DTMF

1001 1110 1xxx xxxx

MOV

DTMF,R

DTMF

(R)

1/1

0011 0100 1000 0iii

MOV

DTCR,I

DTCR

1/1

Shift & Rotate

0100 1101 0xxx xxxx

SHRC

ACC.n, R.n

(R.n+1);

ACC.3, R.3

0; CF

R.0

ZF, CF

1/1

0100 1101 1xxx xxxx

RRC

ACC.n, R.n

(R.n+1);

ACC.3, R.3

CF; CF

R.0

ZF, CF

1/1

0100 1100 0xxx xxxx

SHLC

ACC.n, R.n

(R.n-1);

ACC.0, R.0

0; CF

R.3

ZF, CF

1/1

0100 1100 1xxx xxxx

RLC

ACC.n, R.n

(R.n-1);

ACC.0, R.0

CF; CF

R.3

ZF, CF

1/1

Preliminary W742E81A/W742C81A

- 44 -

Instruction set, continued

Machine code

Mnemonic

Function

Flag affected

W/C

LCD

1001 1000 0xxx xxxx

MOV

LPL, R

LPL

(R)

1/1

1001 1000 1xxx xxxx

MOV

LPH, R

LPH

(R)

1/1

1001 1010 0xxx xxxx

MOV

@LP, R

[(LPH)

10H+(LPL)]

(R)

1/1

1001 1011 0xxx xxxx

MOV

R, @LP

[

(LPH)

10H+(LPL)]

1/1

0000 0010 0000 0000

LCDON

LCD ON

1/1

0000 0010 1000 0000

LCDOFF

LCD OFF

1/1

MFP

0011 0110 0000 000i

MOV

BUZCR, #I

BUZCR

1/1

1000 1010 0xxx xxxx

MOV

BUZCR, R

BUZCR

(R)

1/1

1000 1011 0xxx xxxx

MOV

R,BUZCR

(BUZCR)

1/1

0001 0010 i i i i i i i i

MOV

MFP, #I

[MFP]

1/1

Timer

1010 1010 0xxx xxxx

MOV

TM0L, R

TM0L

(R)

1/1

1010 1010 1xxx xxxx

MOV

TM0H, R

TM0H

(R)

1/1

1010 1011 0xxx xxxx

MOV

TM1L, R

TM1L

(R)

1/1

1010 1011 1xxx xxxx

MOV

TM1H, R

TM1H

(R)

1/1

0001 0011 1000 i00i

MOV

MR0,#I

MR0

(R)

1/1

0001 0011 0000 iiii

MOV

MR1,#I

MR1

(R)

1/1

Other

0000 0000 1000 0000

HOLD

Enter Hold mode

1/1

0000 0000 1100 0000

STOP

Enter Stop mode

1/1

0000 0000 0000 0000

NOP

No operation

1/1

0101 0000 1100 0000

INT

Enable interrupt function

1/1

0101 0000 1000 0000

DIS

INT

Disable interrupt function

1/1

Subroutine

0110 0aaa aaaa aaaa

CALL

Push Stack:
STACK <- PC+1, TAB0, TAB1, TAB2, TAB3,
DBKR, WRP, ROMPR, PAGE, ACC, CF;
PC12~PC0<- (ROMPR)x800H+L10~L0

1/1

0000 0001 iiii iiii

RTN

(PC) <- STACK; Pop other register by I Table
setting (Refer to Table 8)

1/1

Preliminary W742E81A/W742C81A

Publication Release Date: April 2000

- 45 - Revision A1

Table 8 The bit definition of RTN

BIT DEFINITION OF I

I = 0000 0000

Pop

PC from stack only

bit0 = 1

Pop

PC and TAB0, TAB1, TAB2, TAB3 from stack

bit1 = 1

Pop

PC and DBKR from stack

bit2 = 1

Pop

PC and WRP from stack

bit3 = 1

Pop

PC and ROMPR from stack

bit4 = 1

Pop

PC and PAGE from stack

bit5 = 1

Pop

PC and ACC from stack

bit6 = 1

Pop

PC and CF from stack

Headquarters

No. 4, Creation Rd. III,
Science-Based Industrial Park,
Hsinchu, Taiwan
TEL: 886-3-5770066
FAX: 886-3-5792766
http://www.winbond.com.tw/
Voice & Fax-on-demand: 886-2-27197006

Taipei Office

11F, No. 115, Sec. 3, Min-Sheng East Rd.,
Taipei, Taiwan
TEL: 886-2-27190505
FAX: 886-2-27197502

Winbond Electronics (H.K.) Ltd.

Rm. 803, World Trade Square, Tower II,
123 Hoi Bun Rd., Kwun Tong,
Kowloon, Hong Kong
TEL: 852-27513100
FAX: 852-27552064

Winbond Electronics North America Corp.
Winbond Memory Lab.
Winbond Microelectronics Corp.
Winbond Systems Lab.

2727 N. First Street, San Jose,
CA 95134, U.S.A.
TEL: 408-9436666
FAX: 408-5441798

Note: All data and specifications are subject to change without notice.

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: W742C81A

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: W742C81A