ST
Sitronix
ST2202
PRELIMINARY
8 BIT Integrated Microcontroller with 256K Bytes ROM
Notice: This is not a final specification. Some parameters are subject to change.
Ver 2.0a
1
/
65 2003-May-05
1
1
.
.
F
F
E
E
A
A
T
T
U
U
R
R
E
E
S
S
Totally static 8-bit CPU
ROM: 256K x 8-bit
RAM: 4K x 8-bit
Stack: Up to 128-level deep
Operation voltage: 2.4V ~ 5.5V
Operation frequency:
3.0Mhz@2.4V(Min.)
4.0Mhz@2.7V(Min.)
Low Voltage Detector (LVD)
Memory interface to ROM, RAM, Flash
Memory configuration
Three kinds of bank for program, data and interrupts
12-bit bank register supports up to 44M bytes
6 programmable chip-selects with 4 modes
Maximum single device of 16M bytes at
CS5
General-Purpose I/O (GPIO) ports
48 multiplexed CMOS bidirectional bit programmable
I/Os
Hardware de-bounce option for Port-A
Bit programmable pull-up for input pins
Bit programmable pull-up/down and open-drain/CMOS
for Port-C
Programmable Watchdog Timer (WDT)
Timer/Counter
Two 8-bit timer, one can be a 16-bit event counter
One 8-bit Base timer with 5 coexistent interrupt time
settings
Three clocking outputs
Clock sources including Timer0/1, baud rate generator
11 prioritized interrupts with dedicated exception
vectors
External interrupt (edge triggered)
TIMER0 interrupt
TIMER1 interrupt
BASE timer interrupt
PORTA interrupt (transition triggered)
DAC reload interrupt
LCD frame interrupt
SPI interrupts (x2)
UART interrupts (x2)
Dual clock sources with warm-up timer
Low frequency crystal oscillator (OSCX)
32768 Hz
RC oscillator (OSC) 500K ~ 4M Hz
High frequency crystal/resonator oscillator
(Bonding
option) 455K~4M
Hz
Direct Memory Access (DMA)
Block-to-Block transfer
Block to Single port
LCD Controller (LCDC)
Software programmable screen size up to 240X120
(including 160x160, 160x80, etc.)
Support 1-, 4-bit LCD data bus
Share system memory with display memory
Unique internal bus for memory sharing with no loss of
the CPU time
Diverse functions including virtual screen , panning ,
scrolling , contrast control and alternating signal
generator
Support software 16 gray levels
Universal Asynchronous Receiver/Transmitter (UART)
Full-duplex operation
Baud rate generator with one digital PLL
Standard baud rates of 600 bps to 115.2 kbps
Direct glueless support of IrDA physical layer protocol
Two sets of I/Os (TX,RX) for two independent devices
Serial Peripheral Interface (SPI)
Master and slave modes
5 serial signals including enable and data-ready
One stage buffer for transmitter and receiver for
continuous data exchange
Programmable data length from 7-bit to 16-bit
Programmable Sound Generator (PSG)
Two channels with three playing modes
Tone/noise generator
16-level volume control
8-bit PWM DAC for speech/voice
Two dedicated outputs for directly driving and large
current
Three power down modes
WAI0 mode
WAI1 mode
STP mode
Sitronix ST2202
Ver 2.0a
2/65
2003-May-05
2
2
.
.
G
G
E
E
N
N
E
E
R
R
A
A
L
L
D
D
E
E
S
S
C
C
R
R
I
I
P
P
T
T
I
I
O
O
N
N
The ST2202 is a 8-bit integrated microcontroller designed with
CMOS silicon gate technology. The true static CPU core,
power down modes and dual oscillators design makes the
ST2202 suitable for power saving and long battery life designs.
The ST2202 integrates various logic to support functions
on-chip which are needed by system designers. This is also
important for lower system complexity, small board size and, of
course, shorter time to market and less cost.
The ST2202 features the capacity of memory access of
maximum 44M bytes which is needed by products with large
data bases, and also DMA function for fast memory transfer.
Six chip selects are equipped for direct connection to external
ROM, SRAM, Flash memory or other devices. Maximum one
single device of 16M bytes is possible.
The ST2202 has 48 I/Os grouped into 6 ports, Port-A ~ Port-E
and Port-L. Each pin can be programmed to input or output.
There are two options: pull-up/down for inputs of Port-C and
only pull-up for inputs of the other ports. In case of output,
there are open-drain/CMOS options for outputs of PortC and
only CMOS for the other ports. Port-A/B is designed for
keyboard scan with de-bounce and transition triggered interrupt
at Port-A, while Port-C/D/E/L are shared with other system
functions. All the properties of I/O pins are still programmable
when they are assigned to another function. This enlarges the
flexibility of the usage of function signals.
The ability of driving large LCD panels, up to 240x120, and
software 16-gray-level support may rich the display information
and the diversity of contents as well. This is done with no need
of external display RAM because of the internal memory
sharing design.
The ST2202 equips serial communication ports of one UART
and one SPI to perform different communications, ex.: RS-232
and IrDA, with system components or other products such as
PC, Notebook, and popular PDA. Three clocking outputs can
produce synthesized PWM signals or high frequency carrier for
IR remote control. This helps products become more useful in
our daily life.
The built-in two channel PSG/one channel PWM DAC are for
the production of key tone, melody, voice, and speech. Two
dedicated pins can drive a buzzer directly for minimum cost.
With these integrated functions inside, the ST2202 single chip
microcontroller is a right solution for PDA, translator, databank
and other consumer products.
Clock
Generator
OSC
Clock
Generator
OSCX
OSCI
OSCXI
OSCXO
XIO
VCC
GND
Power On
Reset
RESET
A[22:0]
D[7:0]
8-bit
External
Memory
Bus
RD
WR
PSG /
PWM DAC
PSGO/PSGOB
8-bit Static
CPU
ROM
256K bytes
Baud Rate
Generator
DMA
Base Timer
8-bit
SRAM
4K bytes
WDT
Interrupt
Controller
Bank
Control
Logic
PA7~0
Port-A
De-bounce
Logic
Transition
Detector
PB7~0
Port-B
UART with
IrDA Mode
SPI
INTX/PC0
Port-C
SCK/PC1
SDI/PC2
SDO/PC3
TXD0/PC6
Port-C
RXD0/PC7
Port-C
TEST1/2
Chip Select
Logic
MMD/CS0
Port-D
Timer 0/1
8-bit
Clocking
Output
Port-E
TCO0/PE0
PE7~2
Port-E
LCD
Controller
Port-L
LD[3:0]/PL3~0
CP/PL4
AC/PL5
LOAD/PL6
FLM/PL7
TXD1/PD6
RXD1/PD7
Port-D
/PC5
DATA_READY
/PC4
SS
0
~
/PD4
1
~
CS5
/PD5
/A23
CS6
POFF
BLANK
TCO1/PE1
BCO/PE2
PVCC/PGND
XMD
FIGURE 2-1 ST2202 Block Diagram
Sitronix ST2202
Ver 2.0a
3/65
2003-May-05
3
3
.
.
S
S
I
I
G
G
N
N
A
A
L
L
D
D
E
E
S
S
C
C
R
R
I
I
P
P
T
T
I
I
O
O
N
N
S
S
TABLE 3-1 Signal Function Groups
Function Group
Pad No.
Designation
Description
Power
17, 52,
90
VCC , PVCC
VCC: Power supply for system
PVCC: Power supply for PSGO and PSGOB
Ground
22, 48,
49, 71
GND , PGND
GND: System power ground
PGND: Power ground for PSGO and PSGOB
System control
15,
1, 77,
26
RESET , TEST1/2
MMD/
CS0
RESET : Active low system reset signal input
TEST1/2: Leave them open when normal operation
MMD/CS0: Memory modes selection pin
Normal mode: Enable internal ROM.
MMD/
CS0
connects to GND.
Emulation mode: Disable internal ROM.
MMD/
CS0
connects to chip-select pin of external ROM.
One resistor should be added between VCC and this pin.
After reset cycles, MMD/
CS0
changes to be an output, and
outputs signal
CS0
.
Clock
16,
18~21
OSCXO, OSCXI, OSCI,
XIO, XMD
XMD: High frequency oscillator (OSC) mode selection input
Low: Crystal mode. One crystal or resonator should be
connected between OSCI and XIO
High: Resistor oscillator mode. One resistor should be
connected between OSCI and VCC
OSCXI, OSCXO: Connect one 32768Hz crystal between these
two pins when using low frequency oscillator
69, 70
WR
,
RD
External memory R/W control signals
2~4,
81~89,
91~101
A[22:0]
External memory address bus
External memory
bus signals
72~76,
78~80
D[7:0]
External memory data bus
PSG/PWM DAC
50, 51
PSGO, PSGOB
PSG outputs. Connect to one buzzer or speaker
Keyboard scan
signal (return line)
23~25,
27~31
PA7~0
I/O port A
GPIO 32~39
PB7~0
I/O
port
B
Chip selects
61~66
CS6
/A23/PD5 ,
1
~
CS5
/PD4~0
I/O port D and chip-select outputs
UART
46, 47,
67, 68
RXD0/PC7 ,
TXD0/PC6 ,
RXD1/PD7 , TXD1/PD6
UART signals and I/Os
SPI 41~45
DATA_READY
/PC5 ,
SS
/PC4 , SDO/PC3 ,
SDI/PC2 , SCK/PC1
SPI signals and I/Os
PDF 
ZIP
