RF Monolithics, Inc.

Phone: (972) 233-2903

Fax: (972) 387-8148

E-mail: info@rfm.com

Page 1 of 12

RFM Europe

Phone: 44 1963 251383

Fax: 44 1963 251510

http://www.rfm.com

SF1115A-100605

Electrical Characteristics

Characteristic

Sym

Notes

Min

Typ

Max

Units

Nominal Center Frequency

199.000

MHz

Passband

Insertion Loss at fc

7.0

1 db Passband

1, 2

±100

kHz

Amplitude Ripple over fc±100 kHz

0.5

P-P

Group Delay Variation over fc ±100 kHz

GDV

500

P-P

Rejection

Room Temperature fc+800 to fc+400 kHz

1, 2, 3

Room Temperature fc-800 to fc-400 kHz

fc-800 to fc-600 and fc+600 to fc+800 kHz

fc-30 MHz to fc-800 kHz

fc+800 kHz to fc+17 MHz

fc-80 MHz to fc-30 MHz

fc+17 Mhz to fc+80 MHz

Operating Temperature Range

-35

+85

°C

Frequency Temperature Coefficient

FTC

0.032

ppm/°C

SM9171-10

Designed for GSM BTS Receiver IF Applications

Compatible with National Semiconductor Chip Set

Very Flexible Impedance Matching

Unbalanced or Balanced Input or Output

9.1 x 7.1 mm Version of the SF1115A-1

Complies with Directive 2002/95/EC (RoHS)

Absolute Maximum Ratings

Rating

Value

Units

Maximum Incident Power in Passband

+15

dBm

Max. DC voltage between any 2 terminals

VDC

Storage Temperature Range

-40 to +85

°C

Suitable for lead-free soldering - Max. Soldering Profile

260°C for 30 s

199 MHz

SAW Filter

SF1115A

Connection

Terminals

Port 1 Hot

Port 1 Gnd Return

Port 2 Hot

Port 2 Gnd Return

Case Ground

All others

Electrical Connections

Impedance Matching to 50

Unbalanced

External L-C

Impedance Matching to 200

Balanced

External L-C

Impedance Matching to 50

Input / 400

Output

External L-C

Case Style

SMP9171-10 9.1 x 7.1 mm Nominal Footprint

Lid Symbolization (YY = year, WW = week)

RFM SF1115A YYWW

Notes:
1.

Unless noted otherwise, all specifications apply over the operating temperature range with filter
soldered to the specified demonstration board with impedance matching to 50

and measured

with 50

network analyzer.

Unless noted otherwise, all frequency specifications are referenced to the nominal center fre-
quency, fc.

Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in
final user application is dependent on PCB layout and external impedance matching design.
See Application Note No. 42 for details.

The turnover temperature, T

, is the temperature of maximum (or turnover) frequency, f

. The

nominal frequency at any case temperature, T

, may be calculated from: f=f

[1-FTC(T

-T

)

The design, manufacturing process, and specifications of this filter are subject to change.

Either Port 1 or Port 2 may be used for either input or output in the design. However, imped-
ances and impedance matching may vary between Port 1 and Port 2, so that the filter must
always be installed in one direction per the circuit design.

US and international patents may apply.

Electrostatic Sensitive Device. Observe precautions for handling.

199 MHz SAW Filter

RF Monolithics, Inc.

Phone: (972) 233-2903

Fax: (972) 387-8148

E-mail: info@rfm.com

Page 3 of 12

RFM Europe

Phone: 44 1963 251383

Fax: 44 1963 251510

http://www.rfm.com

SF1115A-100605

Case Dimensions

Dimension

Inches

Min

Nom

Max

Min

Nom

Max

8.86

9.09

9.40

0.349

0.358

0.370

6.88

7.11

7.40

0.271

0.280

0.291

1.91

2.00

0.075

0.079

0.99

0.039

0.79

0.031

1.0

0.039

2.54

0.100

10-Terminal Ceramic Surface-Mount Case

9.1 x 7.1 mm Nominal Footprint

SM9171-10 Case

Electrical Connections

Connection

Terminals

Port 1

Input or Return

Return or Input

Port 2

Output or Return

Return or Output

Ground

All others

Single Ended Operation

Return is ground

Differential Operation

Return is hot

Materials

Solder Pad
Termination

Au plating 30 - 60 µinches (76.2-152 µm) over 80-
200 µinches (203-508 µm) Ni.

Lid

Fe-Ni-Co Alloy Electroless Nickel Plate (8-11%
Phosphorus) 100-200 µinches Thick

Body

Ceramic

Pb Free

(10 Places)

(10 Places) D

199 MHz SAW Filter

RF Monolithics, Inc.

Phone: (972) 233-2903

Fax: (972) 387-8148

E-mail: info@rfm.com

Page 5 of 12

RFM Europe

Phone: 44 1963 251383

Fax: 44 1963 251510

http://www.rfm.com

SF1115A-100605

Reference Designator

Value

Additional Information

4.7 pF

0805 Presido ± 0.25pF

4.7 pF

0805 Presido ± 0.25pF

270 nH

1008 Coilcraft Q=65 @ 350MHz 10%

330 nH

1008 Coilcraft Q=65 @ 350MHz 10%

18 pF

0805 Presido ± 0.25pF

18 pF

0805 Presido ± 0.25pF

xfmr1

1:4

ADT 4-1UT, 300-600MHz

xfmr2

4:1

ADT 4-1UT, 300-600MHz

SAW Matching Components

199 MHz SAW Filter

RF Monolithics, Inc.

Phone: (972) 233-2903

Fax: (972) 387-8148

E-mail: info@rfm.com

Page 7 of 12

RFM Europe

Phone: 44 1963 251383

Fax: 44 1963 251510

http://www.rfm.com

SF1115A-100605

COVER TAPE SIZE

COVER TAPE

0.32 mm ±0.3

2.15 mm ±0.2

(CARRIER TAPE SIZE)

(PITCH)

1.5 mm +0.1

-0.0

4.0 mm ±0.1

2.0 mm ±0.1

1.75 mm ±0.1

7.5 mm ±0.1

1.5 mm +0.3

-0.0

PIN #1

USER DIRECTION OF FEED

COMPONENT ORIENTATION and DIMENSIONS

Carrier Tape Dimensions

7.55 mm

±0.1

9.59 mm

±0.1

2.30 mm

±0.1

Pitch

12.0 mm

±0.1

16.0 mm

±0.3

199 MHz SAW Filter

RF Monolithics, Inc.

Phone: (972) 233-2903

Fax: (972) 387-8148

E-mail: info@rfm.com

Page 8 of 12

RFM Europe

Phone: 44 1963 251383

Fax: 44 1963 251510

http://www.rfm.com

SF1115A-100605

Leader and Trailer specifications (Based upon EIA-481)

7 Inch Reel Quantity 500

Symbol

Dimension

178

-4

±1

+0.5

-0.2

20.2

+1.5

-0

±0.5

16.4

-0

22.4

MAX

13 Inch Reel Quantity 2000

Symbol

Dimension

330

-4

100

±2

+0.5

-0.2

20.2

+1.5

-0

±0.5

16.4

-0

22.4

MAX

Dimensions of the leader and trailer

Dimensional drawing of the reel

199 MHz SAW Filter

RF Monolithics, Inc.

Phone: (972) 233-2903

Fax: (972) 387-8148

E-mail: info@rfm.com

Page 9 of 12

RFM Europe

Phone: 44 1963 251383

Fax: 44 1963 251510

http://www.rfm.com

SF1115A-100605

Additional items
(1) Cover tape peeling strength
The cover tape shall be adhered evenly to the carrier tape along both sides in the pulling direction.
The cover tape peeling strength shall be as follows for an angle between the cover tape and the pulling
direction of 165° to 180° (see the figure) and a peeling speed of 300mm/min. ±10mm/min.
[EIA-481] 0.1N to 1.3N for a tape width of 12 to 56mm

Tape material
(1) Carrier tape [anti-charging treatment: carbon used] Surface resistivity: 1 x 10

or less

Material: Polystyrene or Polycarbonate

(2) Cover tape material: Polyester (anti-charging treated) Surface resistivity: 1 x 10

or less

t = 50 to 100µm width = 13.3mm

Warranty periods
Cover tape peeling strength and mounting performance of stored components.
2-1. Cover tape peeling strength: One year after delivery (Peeling strength: 0.1N to 1.3N)

Number of missing components
There shall not be two or more consecutive missing components. Also, the maximum number of missing
components shall be the larger of one piece or 0.1%.

Storage environment
Keep the product on which taping has been performed to a temperature below 40°C and a humidity within
80% RH. Do not subject in the direct sun.

Fixing method
1. Insert the tip of the carrier tape into the groove.
2. Fix the tip of the cover tape with adhesive tape.

199 MHz SAW Filter

RF Monolithics, Inc.

Phone: (972) 233-2903

Fax: (972) 387-8148

E-mail: info@rfm.com

Page 11 of

12
RFM Europe

Phone: 44 1963 251383

Fax: 44 1963 251510

http://www.rfm.com

7 Inch

Reel

Quanity

Per Reel

Number Reels

Per Carton

External Caton

Dimensions

Reel

Weight

Shipping Carton

Weight

Total

Weight

500

254 x 254 x 127 mm

10 x 10 x 5 inches

896 g

448 g

1344 g

500

254 x 254 x 203 mm

10 x 10 x 8 inches

2240 g

448 g

2688 g

13 Inch

Reel

Quanity

Per Reel

Number Reels

Per Carton

External Caton

Dimensions

Reel

Weight

Shipping Carton

Weight

Total

Weight

2000

356 x 356 x 102 mm

14 x 14 x 4 inches

1288 g

448 g

1736 g

2000

356 x 356 x 178 mm

14 x 14 x 7 inches

2576 g

448 g

3024 g

2000

356 x 356 x 356 mm

14 x 14 x 14 inches

5152 g

448 g

5600 g

Package for Shipment

199 MHz SAW Filter

RF Monolithics, Inc.

Phone: (972) 233-2903

Fax: (972) 387-8148

E-mail: info@rfm.com

Page 12 of

12
RFM Europe

Phone: 44 1963 251383

Fax: 44 1963 251510

http://www.rfm.com

RFM Qualification and Reliability Test

Test

Standard

Test Parameters

Pass / Fail Criteria

Life at
Elevated
Temperature

MIL-STD-202

Method 108

Condition C

1,000 Hours

125°C

Unbiased

Within

Electrical &

Hermetic Spec.

(Note 1)

Temperature
Cycling

JESD22

Method JA-104

Air-to-Air

-55 ×Cto +125 ×C

20 min. Dwell

1,000 cycles

Vibration,
Variable
Frequency

MIL-STD-883

Method 2007

Condition B

50g Max.

4 Cycles, 3 Axis

20 Hz to 2 kHz to

20 Hz

Mechanical
Shock

MIL-STD-883

Method 2002

Condition B

1,500g Max.

5 Shocks

3 Axis

Destructive
Bond
Strength

MIL-STD-883

Method 2011

Condition C

Wire Bond Pull

Strength

2.0 grams

(After Seal)

Die Shear
Strength

MIL-STD-883

Method 2019

Shear Strength

0.6 kg

(Strength/area

limit in

development)

Solderability
(Note 2)

J-STD-002

Method B

8 hr. steam age

245 × C solder

temperature

5 second dwell

>95% wetted

surface

Physical
Dimensions

JESD22

Method JB-100

Critical

Dimensions

Within

specifications

Temperature
Characteristics

RFM Procedure

Frequency over

Temperature

Within

specifications

Terminal
Strength
(Note 2)

MIL-STD-833

Method 2004

Condition A & D

Cond. A-Lead

Tension

Cond. B -Pad

Adhesionr 24

8 oz. - 30 sec.

Visual Requirements

& meets

Hermetic Spec.

Resistance to
Solvents

MIL-STD-883

Method 2015

Solvents a, b, d

Visual

Requirements

Steady State
Life

MIL-STD-883

Method 1005

1,000 Hours

Max. Operating

Temperature

Rated Voltage

Within

Electrical &

Hermetic Spec.

(Note 1)

Internal Water-
Vapor Content

MIL-STD-883

Method 1018

< 5,001 PPM

Constant
Acceleration

MIL-STD-883

Method 2001

Y1 Direction

30,000g

Within

Electrical &

Hermetic Spec.

(Note 1)

Substrate
Attach Strength

MIL-STD-883

Method 2027

Tensile Strength of

Die Attachment

Custom per Device

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: SF1115A

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: SF1115A