168-pin Low Profile SDRAM DIMMs
Data Sheet
32MB, 64MB, 128MB, 256MB, 512MB
Enhanced Memory Systems Inc., 1850 Ramtron Dr., Colo Spgs, CO 80921
2001 Enhanced Memory Systems. All rights reserved.
PHONE: (800) 545-DRAM; FAX: (719) 488-9095;
http://www.edram.com
The information contained herein is subject to change without notice.
Revision 1.1
Page 1 of 20
Features
JEDEC Standard 168-pin PC133 SDRAM DIMM
Low Profile for 1U Rack Mount Systems
Fast 5.4 ns Clock Access Time
Supports CAS Latency = 2, 3
On-board Serial Presence Detect (SPD)
Unbuffered 168-pin DIMM
4K Refresh / 64 ms (8K refresh for 512MB DIMM)
Single 3.3V
0.3V Power Supply
Description
The Enhanced Memory Systems 32MB, 64MB, 128MB,
256MB, and 512MB low profile PC133 SDRAM DIMMs
are the best low cost memory option for a wide range of
applications requiring PC66, PC100, or PC133 speeds. The
low profile (1.15 inch) form factor is ideal for 1U rack
mount systems. The fast 5.4 ns clock access time allows
unbuffered DIMM operation at 133 MHz.
The 32MB module is organized as 4Mx64, the 64MB
module is organized as 8Mx64, the 128MB module is
organized as 16Mx64, the 256MB module is organized as
32Mx64, and the 512MB module is organized as 64Mx64.
The ECC modules have x72 organization. Each module
contains a serial presence EEPROM, which contains
information on the module type, module organization,
component speed, and other attributes relevant to the system
controller.
Pin Symbol Pin Symbol Pin Symbol Pin Symbol
1 Vss 43 Vss 85 Vss 127 Vss
2 DQ0 44 DNU 86 DQ32 128 CKE0
3 DQ1 45 S2# 87 DQ33
129 S3#
4 DQ2 46 DQMB2 88 DQ34 130 DQMB6
5 DQ3 47 DQMB3 89 DQ35 131 DQMB7
6 Vdd 48 DNU 90 Vdd 132 RFU
7 DQ4 49 Vdd 91 DQ36
133 Vdd
8 DQ5 50 NC 92 DQ37
134 NC
9 DQ6 51 NC 93 DQ38
135 NC
10 DQ7 52 CB2 94 DQ39 136 CB6
11 DQ8 53 CB3 95 DQ40 137 CB7
12 Vss 54 Vss 96 Vss 138 Vss
13 DQ9 55 DQ16 97 DQ41 139 DQ48
14 DQ10 56 DQ17 98 DQ42 140 DQ49
15 DQ11 57 DQ18 99 DQ43 141 DQ50
16 DQ12 58 DQ19 100 DQ44 142 DQ51
17 DQ13 59 Vdd 101 DQ45 143 Vdd
18 Vdd 60 DQ20 102 Vdd 144 DQ52
19 DQ14 61 NC 103 DQ46 145 NC
20 DQ15 62 NC 104 DQ47 146 NC
21 CB0 63 CKE1 105 CB4 147 NC
22 CB1 64 Vss 106 CB5 148 Vss
23 Vss 65 DQ21 107 Vss 149 DQ53
24 NC 66 DQ22
108 NC 150
DQ54
25 NC 67 DQ23
109 NC 151
DQ55
26 Vdd 68 Vss 110 Vdd 152 Vss
27 WE# 69 DQ24 111 CAS# 153 DQ56
28 DQMB0 70 DQ25 112 DQMB4 154 DQ57
29 DQMB1 71 DQ26 113 DQMB5 155 DQ58
30 S0# 72 DQ27 114 S1# 156 DQ59
31 DNU 73 Vdd 115 RAS# 157 Vdd
32 Vss 74 DQ28 116 Vss 158 DQ60
33 A0 75 DQ29
117 A1 159
DQ61
34 A2 76 DQ30
118 A3 160
DQ62
35 A4 77 DQ31
119 A5 161
DQ63
36 A6 78 Vss 120 A7 162 Vss
37 A8 79 CK2 121 A9 163 CK3
38 A10/AP 80
NC 122 BA0 164 NC
39 BA1 81 WP 123 A11 165 SA0
40 Vdd 82 SDA 124 Vdd 166 SA1
41 Vdd 83 SCL 125 CK1 167 SA2
42 CK0 84 Vdd 126 A12 168 Vdd
168-pin Low Profile SDRAM DIMMs
32MB, 64MB, 128MB, 256MB, 512MB
Data
Sheet
Enhanced Memory Systems Inc., 1850 Ramtron Dr., Colo Spgs, CO 80921
2001 Enhanced Memory Systems. All rights reserved.
PHONE: (800) 545-DRAM; FAX: (719) 488-9095;
http://www.edram.com
The information contained herein is subject to change without notice.
Page 2 of 20
Revision 1.1
Pin Descriptions
Symbol Type
Function
CK(0:3) Input
Clocks: All SDRAM input signals are sampled on the rising edge of CK.
CKE(0:1) Input
Clock Enables: CKE activate (high) or deactivate (low) the CK signals. Deactivating the clock initiates the
Power-Down and Self-Refresh operations (all banks idle), or Clock Suspend operation. CKE is synchronous until
the device enters Power-Down and Self-Refresh modes where it is asynchronous until the mode is exited.
S(0:3)# Input
Chip Select: S# enables (low) or disables (high) the command decoder. When the command decoder is
disabled, new commands are ignored but previous operations continue.
RAS#, CAS#,
WE#
Input
Command Inputs: Sampled on the rising edge of CK, these inputs define the command to be executed.
BA(0:1)
Input
Bank Addresses: These inputs define to which of the 4 banks a given command is being applied.
A(0:12) Input
Address Inputs: A0-A12 define the row address during the Bank Activate command. A0-A8 define the column
address during Read and Write commands. A10/AP invokes the Auto-precharge operation. During manual
Precharge commands, A10/AP low specifies a single bank precharge while A10/AP high precharges all banks.
The address inputs are also used to program the Mode Register.
DQ(0:63)
Input/
Output
Data I/O: Data bus inputs and outputs. For Write cycles, input data is applied to these pins and must be set-up
and held relative to the rising edge of clock. For Read cycles, the device drives output data on these pins after
the CAS latency is satisfied.
DQMB(0:7) Input
Data I/O Mask Inputs: DQMB0-7 inputs mask write data (zero latency) and acts as a synchronous output enable
(2-cycle latency) for read data.
CB(0:7)
Input/
Output
ECC Check Bits
V
DD
Supply
Power Supply: +3.3 V
V
SS
Supply
Ground
SDA
Input/
Output
Serial Presence-Detect Data: SDA is a bi-directional pin used to transfer addresses and data into
and data out of the presence-detect portion of the module.
SCL Input
Serial Clock for Presence-Detect: SCL is used to synchronize the presence detect data transfer to
and from the module
SA(0:2)
Input
Presence-Detect Address Inputs: These pins are used to configure the presence detect device.
WP Input
Serial Presence Detect Write Protect: Active high inhibits writes to the SPD EEPROM. WP must be driven low
for normal read/write operations.
RFU
-
Reserved for Future Use: These pins should be left unconnected.
DNU
-
Do not use.
NC
-
No connect - open pin.
168-pin Low Profile SDRAM DIMMs
Data Sheet
32MB, 64MB, 128MB, 256MB, 512MB
Enhanced Memory Systems Inc., 1850 Ramtron Dr., Colo Spgs, CO 80921
2001 Enhanced Memory Systems. All rights reserved.
PHONE: (800) 545-DRAM; FAX: (719) 488-9095;
http://www.edram.com
The information contained herein is subject to change without notice.
Revision 1.1
Page 3 of 20
32MB DIMM Functional Block Diagram SM3208LDT
U0
U2
DQ(15:0)
DQMB0
S0#
DQ(47:32)
DQMB1
U1
U3
DQ(31:16)
DQMB2
S2#
DQ(63:48)
DQMB3
Clock Wiring
2 SDRAM+15 pf
Termination
2 SDRAM+15 pf
Termination
CK0
CK1
CK2
CK3
10
CK0,2
SDRAMs
Clock Termination
10
CK1,3
Serial PD
SCL
SA0-2
SDA
10 pf
47K
WP
BA1 SDRAM U0-3
BA1
BA0 SDRAM U0-3
BA0
RAS# SDRAM U0-3
RAS#
A0-A11 SDRAM U0-3
A0-A11
Vdd SDRAM U0-3
Vdd
Vss SDRAM U0-3
Vss
CAS# SDRAM U0-3
CAS#
WE# SDRAM U0-3
WE#
CKE SDRAM U0-3
CKE0
Note:
All DQ resistor values are 10 ohms.
All CK resistor values are 10 ohms.
U0-U3 are 4Mx16 PC133 SDRAM Devices.
DQMB7
DQMB6
DQMB4
DQMB5
168-pin Low Profile SDRAM DIMMs
32MB, 64MB, 128MB, 256MB, 512MB
Data
Sheet
Enhanced Memory Systems Inc., 1850 Ramtron Dr., Colo Spgs, CO 80921
2001 Enhanced Memory Systems. All rights reserved.
PHONE: (800) 545-DRAM; FAX: (719) 488-9095;
http://www.edram.com
The information contained herein is subject to change without notice.
Page 4 of 20
Revision 1.1
64MB DIMM Functional Block Diagram SM6408LDT
U0
U1
DQ(7:0)
DQMB0
S0#
DQ(15:8)
DQMB1
U2
U3
DQ(23:16)
DQMB2
S2#
DQ(31:24)
DQMB3
U4
U5
DQ(39:32)
DQMB4
DQ(47:40)
DQMB5
U6
U7
DQ(55:48)
DQMB6
DQ(63:56)
DQMB7
Clock Wiring
4 SDRAM+3.3 pf
Termination
4 SDRAM+3.3 pf
Termination
CK0
CK1
CK2
CK3
10
CK0,2
SDRAMs
Clock Termination
10
CK1,3
Serial PD
SCL
SA0-2
SDA
10 pf
47K
WP
BA1 SDRAM U0-7
BA1
BA0 SDRAM U0-7
BA0
RAS# SDRAM U0-7
RAS#
A0-A11 SDRAM U0-7
A0-A11
Vdd SDRAM U0-7
Vdd
Vss SDRAM U0-7
Vss
CAS# SDRAM U0-7
CAS#
WE# SDRAM U0-7
WE#
CKE SDRAM U0-7
CKE0
Note:
All DQ resistor values are 10 ohms.
All CK resistor values are 10 ohms.
U0-U7 are 8Mx8 PC133 SDRAM Devices.
168-pin Low Profile SDRAM DIMMs
Data Sheet
32MB, 64MB, 128MB, 256MB, 512MB
Enhanced Memory Systems Inc., 1850 Ramtron Dr., Colo Spgs, CO 80921
2001 Enhanced Memory Systems. All rights reserved.
PHONE: (800) 545-DRAM; FAX: (719) 488-9095;
http://www.edram.com
The information contained herein is subject to change without notice.
Revision 1.1
Page 5 of 20
64MB ECC DIMM Functional Block Diagram SM6409LDT
U0
U1
DQ(7:0)
DQMB0
S0#
DQ(15:8)
DQMB1
U3
U4
DQ(23:16)
DQMB2
S2#
DQ(31:24)
DQMB3
U5
U6
DQ(39:32)
DQMB4
DQ(47:40)
DQMB5
U7
U8
DQ(55:48)
DQMB6
DQ(63:56)
DQMB7
U2
CB(7:0)
Clock Wiring
5 SDRAM
Termination
4 SDRAM+3.3 pf
Termination
CK0
CK1
CK2
CK3
10
CK0,2
SDRAMs
Clock Termination
10
CK1,3
Serial PD
SCL
SA0-2
SDA
10 pf
47K
WP
BA1 SDRAM U0-8
BA1
BA0 SDRAM U0-8
BA0
RAS# SDRAM U0-8
RAS#
A0-A11 SDRAM U0-8
A0-A11
Vdd SDRAM U0-8
Vdd
Vss SDRAM U0-8
Vss
CAS# SDRAM U0-8
CAS#
WE# SDRAM U0-8
WE#
CKE SDRAM U0-8
CKE0
Note:
All DQ resistor values are 10 ohms.
All CK resistor values are 10 ohms.
U0-U8 are 8Mx8 PC133 SDRAM Devices.