.220
.010
5,59 0,25
.050
1,27
X 7
.350
8,89
.020
MIN
0,51
Date Code Cntry of Origin
.420
10,67
.295
7,49
.018
0,46
X 16
.004/0,10
16 SURFACES
08
SUGGESTED PAD LAYOUT
.350
8,89
.050
1,27
.090
2,29
.280
7,11
.460
11,68
.030
0,76
A680X
.005
.015
0,13 0,38
.500
.010
12,70 0,25
1
3
6
8
16
14
11
9
1:1
T1
1:1
T2
Part Turns Ratio
Primary Inductance
DCR Hi-Pot
Rise Time Low Frequency
Number (6%)
OCL (H MIN)
(
MAX) (Vrms)
(ps MAX) Cutoff
(@ 20 mVrms, 100 kHz) 20-80% (-3 dB)
A6801 1CT:1CT 5.50 0.21 1500 350 < 2.5 MHZ
A6802 1:1 5.50 0.21 1500 280 < 2.5 MHZ
GIGABIT DUAL
TRANSFORMERS
For Use with 150
Twinax Cable
A100.A (1/99)
Mechanical Schematics
A680X
Dimensions: Inches
mm
Unless otherwise specified, all tolerances are .005
0,13
Compliant with ANSI X3T9.5, FC-PH-3 Fibre
Channel Physical Layer Specification
Compliant with IEEE 802.3z PMD
Designed for fast rise-time and a low frequency
cutoff of 2.5 MHz
IC grade transfer-molded package withstands
235C peak temperature profile
U.S.A: TEL 619 674 8100
EUROPE: TEL 441 483 401 700
ASIA: TEL 886 7 821 3141
WEB: http://www.pulseeng.com
Electrical Specifications @ 25C -- Operating Temperature 0C to 70C
Weight . . . . . . . . . . . .1.4 grams
Tape & Reel . . . . . . . . .500/reel
Tube . . . . . . . . . . . . . . .45/tube
NOTE: For lower speed Fibre Channel applications, please refer to application note on data sheet A101.
1:1
2
1
3
7
6
8
15
16
14
10
11
9
T1
1:1
T2
A6801
A6802
1.
R1 and R2 values should be based upon the transmit
amplitude required for the system. Placing a short
(0
) will result in maximum amplitude. However,
doing so will result in distortion on the output due to
impedance mismatch. For optimum design, R1 and
R2 should be approximately 68
for each leg. This
will result in a -6.0 dB insertion loss (transmitter
section). If this is too much insertion loss, then at
least a 15
for R1 and R2 is recommended.
Insertion Loss of Transmitter:
Req = R1 + R2 and Zo = 150
Insertion Loss = 20 log [Zo / Req + Z0]
2.
When designing PCB layout, transmission line
methods must be utilized to maintain return loss and
signal integrity. Transformer should be located within
1" of cable connector.
3.
tr
transformer
=
[ (tr
out
)
2
- (tr
in
)
2
]
4.
The typical application circuit shown above is a sug-
gested layout. Actual board layout may vary based
upon individual applications and EMC concerns.
NOTE:
These gigabit dual transformers are packaged in tubes unless Tape &
Reel is specified. When ordering, add the suffix "T" (i.e. A6801T) for
"Tape & Reel" packaging in increments of 500.
For More Information :
Corporate
12220 World Trade Drive
San Diego, CA 92128
Tel:
619 674 8100
FAX: 619 674 8262
http://www.pulseeng.com
Quick-Facts: 619 674 9672
Europe
1 & 2 Huxley Road
The Surrey Research Park
Guildford, Surrey GU2 5RE
United Kingdom
Tel:
44 1483 401700
FAX: 44 1483 401701
Asia
150 Kampong Ampat
#07-01/02
KA Centre
Singapore 368324
Tel: 65 287 8998
FAX: 65 280 0080
Distributor
GIGABIT DUAL
TRANSFORMERS
For Use with 150
Twinax Cable
Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product
names mentioned herein may be trademarks or registered trademarks of their respective owners.
A100.A (1/99)
Printed on recycled paper. 1999, Pulse Engineering, Inc.
Application Notes:
Pulse has designed Gigabit Dual Transformers speci-
fically for point to point coupling to 150
Twinax cable.
The isolation transformers protect the station from static
charges that may develop on the cable and prevent
ground loop currents from being transferred between
stations. The devices have also been designed to provide
common mode rejection within the transmission band and
thus reduce EMI. The bandwidth of these devices
minimizes data dependent jitter by providing fast signal
rise times. The dual package allows connection of both
the transmit and receive channels as shown in the
application circuit below. Surface mount packaging also
allows a cost effective solution. The transformers are
available in either tubes or Tape & Reel packaging.
C3
Chassis Gnd.
D.C. Gnd.
C4
SERDES
CHIP SET
HSDCC OR DB9
CONNECTOR
VCC GND
120 200
VCC
GND
75
TRANSMISSION LINES
Chassis Gnd.
D.C. Gnd.
TX+
TX-
RX-
RX+
R1
Chassis Gnd.
Chassis Gnd.
C1
.027 F
C2
.027 F
TX+
TX-
RX-
RX+
A6801
D
A
TE CODE CTR
Y ORIGIN
150
R2
120 200
PDF 
ZIP