ii
Electromagnetic Compatibility Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded cables for SCSI connection external to the cabinet are used in the compliance testing of this Product. LSI
Logic is not responsible for any radio or television interference caused by unauthorized modification of this equipment
or the substitution or attachment of connecting cables and equipment other than those specified by LSI Logic. The
correction of interferences caused by such unauthorized modification, substitution, or attachment will be the
responsibility of the user.
The LSI Logic LSI60800 is tested to comply with FCC standards for home or office use.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du
Canada.
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information
Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may
cause radio interference. Install and use the equipment according to the instruction manual.
LSI Logic Corporation
North American Headquarters
Milpitas, CA
408.433.8000
November 2000
1
Copyright 19982000 by LSI Logic Corporation. All rights reserved.
LSI60800 PCI to USB
Host Adapter
User's Guide
Version 1.1
1 What is Covered in This Guide
This User's Guide provides instructions and illustrations to help you
install a LSI Logic LSI60800 PCI to USB Host Adapter. It covers the
following topics:
Ensuring USB support is available in Windows 98
Installing the LSI60800 Board
Installing the LSI60800 software
Connecting USB devices
The LSI60800 provides a low-cost USB solution for attaching USB
devices (digital video cameras, digital audio speakers, page scanners,
photo scanners, photo printers, etc.) to PCI computer systems. Figure 1
shows the major components and connections of the LSI60800 Board.
The LSI Logic LSI60800 is based on the industry standard OpenHCI
specification. Therefore, no vendor-specific driver is needed. It is
supported by Microsoft in Windows 98, and the upcoming
Windows NT 5.0.
2
LSI60800 PCI to USB Host Adapter
Figure 1
LSI60800 Board
.
2 Hardware Installation
Before you begin the board installation, switch off the power to the
computer and any peripheral devices and disconnect all power cords.
Important:
Before handling the LSI60800 board, ground yourself using
a ground strap attached to the computer metal frame. Static
charges on your body can damage electronic components.
Handle plug-in boards by the edge; do not touch board
components or gold connector contacts.
1.
Remove the cover on your computer to access the PCI slots. Refer
to your computer documentation if necessary.
2.
Locate an unused PCI expansion slot for installing the LSI60800
Board. Refer to your computer documentation if necessary to locate
the expansion slots.
3.
Remove the blank bracket panel on the back of the computer that
covers the slot you intend to use. Save the bracket screw.
J1 PCI
Mainboard
Connector
External
USB Cable
PCI to USB
Controller
J2
LSI60800 PCI to USB Host Adapter
3
4.
Remove the LSI60800 Board from the antistatic bag and insert the
edge connector into the PCI slot, as pictured in Figure 2. Make sure
the edge connector is properly aligned before pressing the board into
place. Apply even pressure to both ends of the board while inserting it.
5.
Visually check to make sure the LSI60800 Board is properly seated,
and is all the way down in the PCI slot.
6.
Screw the bracket down with the screw from step 3.
Figure 2
Inserting the LSI60800 Board
PDF 
ZIP