AC LINE FREQUENCY DIVIDERS
RED SERIES
RED 5/6 Divide by 5 or 6
RED 50/60 Divide by 50 or 60
RED 100/120 Divide by 100 or 120
RED 300/360 Divide by 300 or 360
RED 500/600 Divide by 500 or 600
RED 3000/3600 Divide by 3000 or 3600
FEATURES:
Clock input pulse shaper accepts
50Hz/60Hz sine wave directly
Fully static counter operation
+4.5V to +15V operation (V
DD
- V
SS
)
Low power dissipation
High noise immunity
Reset
Input Enable
50Hz/60Hz division select input
Output low power TTL compatible at +4.5V operation
Square Wave Output (except for 5)
RED x/y (DIP); RED x/y-S (SOIC) See Figure 1
APPLICATION:
Time base generator from either 50 Hz or 60 Hz line
frequency to produce:
10 pulses per second (RED 5/6)
1 pulse per second (RED 50/60)
1 pulse per 2 seconds (RED 100/120)
1 pulse per .1 minute (RED 300/360)
1 pulse per 10 seconds (RED 500/600)
1 pulse per minute (RED 3000/3600)
DESCRIPTION OF OPERATION:
The counter advances by one on each negative transition of the
input clock pulse as long as the Enable signal is High and the
Reset signal is Low. When the Enable signal is Low the input
clock pulses will be inhibited and the counter will be held at the
state it was in prior to bringing the Enable Low. A High Reset
signal clears the counter to zero count.
Depending on the device used, a Low on the Division Select in-
put will cause a Divide by 6, 60, 120, 360, 600 or 3600. A High
on the Division Select will cause a Divide by 5, 50, 100, 300, 500
or 3000.
All outputs are 50% duty cycle except RED 5, where output is
low for two clocks and high for three clocks.
CLOCK INPUT
If input signals are less than the Vss or greater than V
DD
, a
series input resistor should be used to limit the maximum input
current to 2 mA.
MARKING AS FOLLOWS:
PART
MARKING
RED 5/6
RED 6
RED 50/60
RED 60
RED 100/120
RED 120
RED 300/360
RED 360
RED 500/600
RED 600
RED 3000/3600
RED 3600
V
DD
(V+)
LSI
1
2
3
4
8
7
6
5
O U T P U T
R E S E T
V
SS
(-V)
NC
DIVISION SELECT
E N A B L E
CLOCK INPUT
PIN ASSIGNMENT - TOP VIEW
FIGURE 1
The information included herein is believed to be
accurate and reliable. However, LSI Computer Systems,
Inc. assumes no responsibilities for inaccuracies, nor for
any infringements of patent rights of others which may
result from its use.
RED-012703-1
LSI/CSI
LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 271-0400 FAX (631) 271-0405
RED SERIES
UL
A3800
January 2003
MAXIMUM RATINGS:
PARAMETER
SYMBOL VALUE UNIT
Storage Temperature
T
STG
-65 to +150
C
Operating Temperature
T
A
-40 to +85
C
DC Supply Voltage
(V
DD
- Vss)
+18
V
Voltage at any input
V
IN
Vss - 0.3 to V
DD
+ 0.3 V
ENABLE SIGNAL TIMING
If the Enable signal switches Low during a positive clock phase and
then switches High during a negative clock phase, a false count will
be registered. To prevent this from happening, the Enable signal
should not switch Low during a positive clock phase unless the
switch to High also occurs during a positive clock phase. The
Enable signal should normally be switched during a negative clock
phase.
ELECTRICAL CHARACTERISTICS: (TA = 25 unless otherwise specified)
TEST CONDITIONS: Vss = OV
Output Capacitance Load = 15 pF
Input Rise and Fall times = 20 ns,
except clock Rise and Fall times
Input Capacitance = 5pF max (any input)
V
DD
Min Max Units
Quiescent Device Current
5V
-
10
uA
10V
-
20
uA
Output Voltage, Low Level
5V
-
0.0
V
10V
-
0.0
V
High Level
5V
4.99
-
V
10V
9.99
-
V
Clock Input Voltage, Low Level
5V
-
1
V
10V
-
2
V
High Level
5V
4
-
V
10V
8
-
V
Input Noise Immunity
(except clock)
5V
1.5
-
V
(Low and High)
10V
3.0
-
V
Output Drive Current
Full N Channel Sink Current
4.5V
0.18
-
mA
Temp. (Vout = Vss +0.4V)
10V
0.45
-
mA
Range
P Channel Sink Current
4.5V
0.3
-
mA
(Vout = V
DD
-1)
10V
0.75
-
mA
V
DD
MIN
MAX
UNITS
Clock Rise and Fall Time:
5V
No Maximum Limit
-
10V
No Maximum Limit
-
Clock Frequency
5V
DC
600
KHz
10V
DC
1200
KHz
Input Clock Pulse Width
5V
800
-
ns
10V
400
-
ns
Output Rise and Fall Time
5V
-
225
ns
10V
-
150
ns
Propagation Delay to Output
5V
-
1500
ns
10V
-
750
ns
Enable Set-up Time
5V
-
300
ns
10V
-
150
ns
Reset Pulse Width
5V
800
-
ns
10V
400
-
ns
Reset Removal Time
5V
-
1200
ns
10V
-
600
ns
Reset Propagation Delay
5V
-
1400
ns
to Output
10V
-
700
ns
RED-012703-2
CL IN
CL
CL
R
E
E
5
PULSE SHAPER
INPUT CLOCK GENERATOR
6
ENABLE
E
E
2
RESET
R
8
3
4
+4.5V to +15V
GND
N/C
VDD
VSS
7
DIVISION SELECT
DS
3 BIT
JOHNSON
+5/6
3 BIT
JOHNSON
+5/6
3 BIT
JOHNSON
10
5 BIT
JOHNSON
10
3 BIT
JOHNSON
6
5 BIT
JOHNSON
10
1 BIT
2
CL
CL
CL
CL
D3000/3600
D100/120
RED 5/6,50/60,
300/360,3000/3600
RED 100/120
RED 500/600
R
R
CL2
CL2
CL2
CL2
CL1
CL1
CL1
CL1
CL3
CL3
3 BIT
JOHNSON
+5/6
5 BIT
JOHNSON
10
5 BIT
JOHNSON
10
CL
CL
D500/600
R
CL2
CL2
CL1
CL1
D5/6
D50/60
D300/360
1
DS
DS
DS
1
1
1
1
1
FIGURE 2. BLOCK DIAGRAM