LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Features
* Low power consumption.
* High efficiency.
* Versatile mounting on p.c. board or panel.
* I.C. compatible/low current requirement.
* Popular T-1
3/4
diameter.
Package Dimensions
Part No.
Lens
Source Color
LTL2R3CBK5
Water Clear
InGaN Blue
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is 0.25mm(.010") unless otherwise noted.
3. Protruded resin under flange is 1.0mm(.04") max.
4. Lead spacing is measured where the leads emerge from the package.
5. Specifications are subject to change without notice.
Part No. : LTL2R3CBK5
Page : 1 of 10
BNS-OD-C131/A4
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Absolute Maximum Ratings at T
A
=25
Parameter
Maximum
Rating
Unit
Power
Dissipation
135
mW
Peak Forward Current
(1/10 Duty Cycle, 0.1ms Pulse Width)
100 mA
DC Forward Current
30
mA
Derating Linear From 30 0.5
mA/
Reverse
Voltage
5
V
Electrostatic Discharge Threshold(HBM)
Note A
1000
V
Operating Temperature Range
-20 to +
80
Storage Temperature Range
-30 to + 100
Lead Soldering Temperature
[1.6mm(.063") From Body]
260 for 5 Seconds
Note A :
Product resistance to electrostatic discharge (ESD) according to the HBM is measured by simulating ESD using a rapid
avalanche test (RAET). The RAET procedures are designed to approximate the maximum ESD ratings shown.
The RAET procedure is performed on each die. The ESD classification of Class II is based on sample testing according to
MIL-STD 883E. (From CREE official DS).
Part No. : LTL2R3CBK5
Page : 2 of 10
BNS-OD-C131/A4
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Electrical / Optical Characteristics at T
A
=25
Parameter Symbol
Min.
Typ.
Max.
Unit
Test
Condition
Luminous Intensity
I
V
310 1500 mcd
I
F
= 20mA
Note 1,5
Viewing Angle
2
1/2
30
deg
Note 2 (Fig.6)
Peak Emission Wavelength
P
468 nm
Measurement
@Peak (Fig.1)
Dominant Wavelength
d
470
nm
Note 3
Spectral Line Half-Width
26
nm
Forward Voltage
V
F
3.7
4.2
V
I
F
= 20mA
Reverse Current
I
R
20
A
V
R
= 5V
NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE
eye-response curve.
2.
1/2
is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
3. The dominant wavelength, d is derived from the CIE chromaticity diagram and represents the single
wavelength which defines the color of the device.
4. Iv classification code is marked on each packing bag.
5. The Iv guarantee should be added 15% tolerance.
6. Precautions in handling:
When soldering, leave 2mm of minimum clearance from the resin to the soldering point.
Dipping the resin to solder must be avoided.
Correcting the soldered position after soldering must be avoided.
In soldering, do not apply any stress to the lead frame particularly when heated.
When forming a lead, make sure not to apply any stress inside the resin.
Lead forming must be done before soldering.
It is necessary to cut the lead frame at normal temperature.
7. Caution in ESD:
Static Electricity and surge damages the LED. It is recommend to use a wrist band or anti-electrostatic
glove when handling the LED. All devices, equipment and machinery must be properly grounded.
Part No. : LTL2R3CBK5
Page : 3 of 10
BNS-OD-C131/A4
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Typical Electrical / Optical Characteristics Curves
(25 Ambient Temperature Unless Otherwise Noted)
Part No. : LTL2R3CBK5
Page : 4 of 10
BNS-OD-C131/A4
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Packing Spec
500 or 250 pcs per packing bag
10 packing bags per inner carton
total 5000 pcs per inner carton
8 Inner cartons per outer carton
total 40000 pcs per outer carton
In every shipping lot, only the last pack will be non-full packing
Part No. : LTL2R3CBK5
Page : 5 of 10
BNS-OD-C131/A4
PDF 
ZIP