FEATURES
DIRECT REPLACEMENT FOR INTERSIL ID100 & ID101
REVERSE LEAKAGE CURRENT
I
R
= 0.1pA
REVERSE BREAKDOWN VOLTAGE
BV
R
30V
REVERSE CAPACITANCE
C
rss
= 0.75pF
ABSOLUTE MAXIMUM RATINGS
1
@ 25 C (unless otherwise stated)
Maximum Temperatures
Storage Temperature
-65 to +200 C
Operating Junction Temperature
-55 to +150 C
Maximum Power Dissipation
Continuous Power Dissipation
300mW
Maximum Currents
Forward Current
20mA
Reverse Current
100A
Maximum Voltages
Reverse Voltage
30V
Diode to Diode Voltage
50V
ELECTRICAL CHARACTERISTICS @ 25 C (unless otherwise stated)
SYMBOL
CHARACTERISTIC
MIN TYP MAX UNITS
CONDITIONS
BV
R
Reverse Breakdown Voltage
30
I
R
= 1A
V
F
Forward
Voltage
0.8 1.1
V
I
F
= 10mA
0.1
V
R
= 1V
I
R
Reverse Leakage Current
2.0 10
|I
R1
-I
R2
|
Differential Leakage Current
3
pA
V
R
= 10V
C
rss
Total Reverse Capacitance
2
0.75
1
pF
V
R
= 10V, f = 1MHz
ID100
NC
K1
NC
K2
5
BOTTOM VIEW
TO-78
1
2
3
6
7
A1
A2
ID101
NC
K1
A2
K2
3
1
7
5
BOTTOM VIEW
TO-71
6
2
A1
NC
Linear Integrated Systems
ID100 ID101
MONOLITHIC DUAL
PICO AMPERE DIODES
Linear Integrated Systems
4042 Clipper Court Fremont, CA 94538 Tel: 510 490-9160 Fax: 510 353-0261
Figure 1. Operational Amplifier Protection
Input Differential Voltage limited to 0.8V (typ) by Diodes ID100 D
1
and D
2
.
Common Mode Input voltage limited by Diodes ID100 D
3
and D
4
to 15V.
Figure 2. Sample and Hold Circuit
Typical Sample and Hold circuit with clipping. ID100 diodes reduce offset
voltages fed capacitively from the ID100 switch gate.
FIGURE 1
2N4117A
R
2N4393
-V
+V
V
OUT
D2
D1
C
ID100
CONTROL
SIGNAL
e
in
+V
FIGURE 2
-15V
+15V
OP-27
D1
D2
D3
D4
+
-
ID100
TO-78
0.335
0.370
0.305
0.335
0.016
0.019
0.165
0.185
0.040
MAX.
DIM. A
0.016
0.021
DIM. B
MIN. 0.500
0.200
0.100
0.100
0.028
0.034
45
1
2 3
5
6
7
0.029
0.045
SEATING
PLANE
TO-71
Six Lead
0.230
0.209
DIA.
DIA.
0.195
0.175
0.030
MAX.
0.500 MIN.
0.150
0.115
0.019
0.016
DIA.
6 LEADS
3
2
1
5
6
0.046
0.036
45
0.048
0.028
0.100
0.050
7
Linear Integrated Systems
4042 Clipper Court Fremont, CA 94538 Tel: 510 490-9160 Fax: 510 353-0261
1.
Absolute maximum ratings are limiting values above which serviceability may be impaired.
2.
Design reference only, not 100% tested.
3.
Pins 3 & 5 on ID100 and ID101 must not be connected, in any fashion or manner, to any circuit or node.
Information furnished by Linear Integrated Systems is believed to be accurate and reliable. However, no responsibility is assumed for its
use; nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implicatio
otherwise under any patent or patent rights of Linear Integrated Systems.
n or
PDF 
ZIP