ICS671-01
Zero Delay, Low Skew Buffer and Multipler
MDS 671-01 B
1
Revision 051700
Printed 11/15/00
Integrated Circuit Systems, Inc. 525 Race Street San Jose CA95126 (408) 295-9800 tel www.icst.com
Block Diagram
Description
Features
The ICS671-01 is a low phase noise, high speed
PLL based, 8 output, low skew zero delay buffer
and multiplier. Based on ICS's proprietary low
jitter Phase Locked Loop (PLL) techniques, the
device provides eight low skew outputs at speeds
up to 160 MHz at 3.3 V. The ICS671-01 includes
a bank of six outputs running at either x2 or x4
mode, one output running at either x2, x4, or x5
mode, and one more output running at either x1,
x2, or x4 mode. For normal operation, output
clock CLK8 is tied to the FBIN pin.
ICS manufactures the largest variety of clock
generators and buffers, and is the largest clock
supplier in the world.
Packaged in 16 pin narrow SOIC
Clock outputs from 5 to 160 MHz
Zero input-output delay
Integrated x2 or x4 selections, and x5 for CLK7
Eight low-skew (<250 ps) outputs
Full CMOS outputs with 25 mA output drive
capability at TTL levels
Tri-state mode for board-level testing
Advanced, low power, sub-micron CMOS process
3.3 V to 5 V operating voltage
x2, x4, or x5
PLL
CLK1
FBIN
CLK2
S1, S0
2
CLK3
CLK4
CLK5
CLK6
CLK7
CLK8
Control
Logic
CLKIN
ICS671-01
Zero Delay, Low Skew Buffer and Multipler
MDS 671-01 B
2
Revision 051700
Printed 11/15/00
Integrated Circuit Systems, Inc. 525 Race Street San Jose CA95126 (408) 295-9800 tel www.icst.com
Pin Descriptions
Key: I = Input; O = output; P = power supply connection.
Pin Assignment
ICS671-01
External Components
The ICS671-01 requires a minimum number of external components for proper operation. Decoupling
capacitors of 0.01F should be connected between VDD and GND on pins 4 and 5, and VDD and GND
on pins 13 and 12, as close to the device as possible. A series termination resistor of 33
may be used close
to each clock output pin to reduce reflections.
16
15
14
13
16 pin narrow (150 mil) SOIC
12
11
10
9
1
2
3
4
5
6
7
8
CLK1
GND
FBIN
CLKIN
VDD
S0
CLK3
CLK4
VDD
GND
CLK5
S1
CLK6
CLK8
CLK7
CLK2
Number
Name
Type
Description
1
CLKIN
I
Clock Input.
2, 3, 6, 7,
10, 11
CLK1:6
O
Clock Outputs 1:6. See above table.
4, 13
VDD
P
Power supply. Connect both pins to same voltage (either 3.3 V or 5 V).
5, 12
GND
P
Connect to ground.
8
S0
I
Select input 0. See table above.
9
S1
I
Select input 1. See table above.
14
CLK7
I
Clock Output 7. See table above.
15
CLK8
I
Clock Output 8. See table above. Normally use this clock as feedback.
16
FBIN
I
Feedback Input. Connect to CLK8 under normal operations.
S1
S0
CLK1:6
CLK7
CLK8
Input range
0
0
Tri-state (high impedance)
Tri-state (high impedance)
Tri-state (high impedance)
-
0
1
x2
x5
x1
5 to 30 MHz
1
0
x2
x2
x2
15 to 80 MHz
1
1
x4
x4
x4
7.5 to 40 MHz
Output Clock Mode Select Table
ICS671-01
Zero Delay, Low Skew Buffer and Multipler
MDS 671-01 B
3
Revision 051700
Printed 11/15/00
Integrated Circuit Systems, Inc. 525 Race Street San Jose CA95126 (408) 295-9800 tel www.icst.com
Parameter
Conditions
Minimum
Typical
Maximum
Units
ABSOLUTE MAXIMUM RATINGS (n
note 1)
Supply voltage, VDD
Referenced to GND
-0.5
7
V
Inputs and Clock Outputs
Referenced to GND
-0.5
VDD+0.5
V
Electrostatic Discharge
MIL-STD-883
2000
V
Ambient Operating Temperature
0
70
C
Soldering Temperature
Max of 10 seconds
260
C
Junction temperature
150
C
Storage temperature
-65
150
C
DC CHARACTERISTICS (VDD = 3.3 V unless specified ottherwise)
Operating Voltage, VDD
3.13
5.50
V
Input High Voltage, VIH, CLKIN pin only
VDD/2+1
VDD/2
V
Input Low Voltage, VIL, CLKIN pin only
VDD/2
VDD/2-1
V
Input High Voltage, VIH
2
V
Input Low Voltage, VIL
0.8
V
Output High Voltage, VOH
IOH=-25mA
2.4
V
Output Low Voltage, VOL
IOL=25mA
0.4
V
Output High Voltage, VOH, CMOS level
IOH=-8mA
VDD-0.4
V
Operating Suppl Current, IDD (Note 2)
No Load, S1=1, S0=0
25
mA
Operating Suppl Current, IDD (Note 3)
No Load, S1=1, S0=0
74
mA
Short Circuit Current
Each output
50
mA
Input Capacitance
S0, S1, FBIN
7
pF
AC CHARACTERISTICS (VDD = 3.3 V unless specified oth
herwise)
Input Clock Frequency
See table on page 2
5
80
M H z
Output Clock Frequency
See table on page 2
5
160
M H z
Output Clock Rise Time, CL=30pF
0.8 to 2.0V
1.5
ns
Output Clock Fall Time, CL=30pF
2.0 to 0.8V
1.5
ns
Output Clock Duty Cycle, VDD=3.3V
At VDD/2
40
50
60
%
Device to Device Skew, equally loaded
rising edges at VDD/2
700
ps
Output to Output Skew, equally loaded
rising edges at VDD/2
250
ps
Input to Output Skew, FBIN to CLK8
rising edges at VDD/2
350
ps
Maximum Absolute Jitter
300
ps
Cycle to Cycle Jitter, 30pF loads
500
ps
Electrical Specifications
Notes:
1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged
exposure to levels above the operating limits but below the Absolute Maximums may affect device reliability.
2. With CLKIN = 20 MHz, FBIN to CLK8, all outputs at 40 MHz.
3. With CLKIN = 80 MHz, FBIN to CLK8, all outputs at 160 MHz.
ICS671-01
Zero Delay, Low Skew Buffer and Multipler
MDS 671-01 B
4
Revision 051700
Printed 11/15/00
Integrated Circuit Systems, Inc. 525 Race Street San Jose CA95126 (408) 295-9800 tel www.icst.com
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its
use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is
intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does
not authorize or warrant any ICS product for use in life support devices or critical medical instruments.
Ordering Information
Part/Order Number
Marking
Shipping packaging
Package
Temperature
ICS671M-01
ICS671M-01
tubes
16 pin SOIC
0-70 C
ICS671M-01T
ICS671M-01
tape and reel
16 pin SOIC
0-70 C
16 pin SOIC narrow
Inch
hes
Millim
meters
Symbol
Min
Max
Min
Max
A
0.0532
0.0688
1.35
1.75
A1
0.0040
0.0098
0.10
0.24
B
0.0130
0.0200
0.33
0.51
C
0.0075
0.0098
0.19
0.24
D
0.3859
0.3937
9.80
10.00
E
0.1497
0.1574
3.80
4.00
e
.050 BSSC
1.27 BSSC
H
0.2284
0.2440
5.80
6.20
h
0.0099
0.0195
0.25
0.50
L
0.0160
0.0500
0.41
1.27
B
D
E
H
e
A1
C
A
h x 45
L
INDEX
AREA
1
2
Package Outline and Package Dimensions
(
For current dimensional specifications, see JEDEC Publication No. 95.)
PDF 
ZIP