IC41C4405x and IC41LV4405x Series
2
Integrated Circuit Solution Inc.
DR013-0B 10/17/2002
FEATURES
Fast Page Mode Access Cycle
TTL compatible inputs and outputs
Refresh Interval:
-- 2,048 cycles/32 ms
-- 4,096 cycles/64 ms
Refresh Mode:
RAS
-Only,
CAS
-before-
RAS
(CBR), and Hidden
JEDEC standard pinout
Single power supply:
5V 10% or 3.3V 10%
Byte Write and Byte Read operation via
two
CAS
DESCRIPTION
The
ICSI
4405x Series is a 4,194,304 x 4-bit high-performance
CMOS Dynamic Random Access Memory. The Fast Page
Mode allows 2,048 or 4096 random accesses within a single
row with access cycle time as short as 20 ns per 4-bit word.
These features make the 4405x Series ideally suited for high-
bandwidth graphics, digital signal processing, high-performance
computing systems, and peripheral applications.
The 4405x Series is packaged in a 24-pin 300mil SOJ and a 24
pin TSOP-2
4M x 4 (16
-
MBIT) DYNAMIC RAM
WITH FAST PAGE MODE
KEY TIMING PARAMETERS
Parameter
-
50
-
60
Unit
RAS
Access Time (t
RAC
)
5
0
6
0
ns
CAS
Access Time (t
CAC
)
13
15
ns
Column Address Access Time (t
AA
)
25
30
ns
Fast Page Mode Cycle Time (t
PC
)
20
25
ns
Read/Write Cycle Time (t
RC
)
8
4
104
ns
ICSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any errors
which may appear in this publication. Copyright 2000, Integrated Circuit Solution Inc.
PRODUCT SERIES OVERVIEW
Part No.
Refresh
Voltage
IS41C44052
2K
5
V
10%
IS41C44054
4K
5
V
10%
IS41LV44052
2K
3.3V 10%
IS41LV44054
4K
3.3V 10%
1
2
3
4
5
6
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
VCC
I/O0
I/O1
WE
RAS
*A11(NC)
A10
A0
A1
A2
A3
VCC
GND
I/O3
I/O2
CAS
OE
A9
A8
A7
A6
A5
A4
GND
* A11 is NC for 2K Refresh devices.
PIN DESCRIPTIONS
A0-A11
Address Inputs (4K Refresh)
A0-A10
Address Inputs (2K Refresh)
I/O0-3
Data Inputs/Outputs
WE
Write Enable
OE
Output Enable
RAS
Row Address Strobe
CAS
Column Address Strobe
V
cc
Power
GND
Ground
NC
No Connection
PIN CONFIGURATION
24 (26) Pin SOJ, TSOP
-
2
IC41C4405x and IC41LV4405x Series
4
Integrated Circuit Solution Inc.
DR013-0B 10/17/2002
Functional Description
The IC41C4405x and IC41LV4405x are CMOS DRAMs
optimized for high-speed bandwidth, low power
applications. During READ or WRITE cycles, each bit is
uniquely addressed through the 11 or 12 address bits.
These are entered 11 bits (A0-A10) at a time for the 2K
refresh device or 12 bits (A0-A11) at a time for the 4K
refresh device. The row address is latched by the Row
Address Strobe (
RAS
). The column address is latched by
the Column Address Strobe (
CAS
).
RAS
is used to latch
the first nine bits and
CAS
is used the latter ten bits.
Memory Cycle
A memory cycle is initiated by bring
RAS
LOW and it is
terminated by returning both
RAS
and
CAS
HIGH. To
ensures proper device operation and data integrity any
memory cycle, once initiated, must not be ended or
aborted before the minimum t
RAS
time has expired. A new
cycle must not be initiated until the minimum precharge
time t
RP
, t
CP
has elapsed.
Read Cycle
A read cycle is initiated by the falling edge of
CAS
or
OE
,
whichever occurs last, while holding
WE
HIGH. The
column address must be held for a minimum time specified
by t
AR
. Data Out becomes valid only when t
RAC
, t
AA
, t
CAC
and t
OEA
are all satisfied. As a result, the access time is
dependent on the timing relationships between these
parameters.
Write Cycle
A write cycle is initiated by the falling edge of
CAS
and
WE
,
whichever occurs last. The input data must be valid at or
before the falling edge of
CAS
or
WE
, whichever occurs
last.
Refresh Cycle
To retain data, 2,048 refresh cycles are required in each
32 ms period, or 4,096 refresh cycles are required in each
64ms period. There are two ways to refresh the memory:
1. By clocking each of the 2,048 row addresses (A0
through A10) or 4096 row addresses (A0 through A11)
with RAS at least once every 32 ms or 64ms respectively.
Any read, write, read-modify-write or RAS-only cycle
refreshes the addressed row.
2. Using a
CAS
-before-
RAS
refresh cycle.
CAS
-before-
RAS
refresh is activated by the falling edge of
RAS
,
while holding
CAS
LOW. In
CAS
-before-
RAS
refresh
cycle, an internal 11(12)-bit counter provides the row
addresses and the external address inputs are ignored.
CAS
-before-
RAS
is a refresh-only mode and no data
access or device selection is allowed. Thus, the output
remains in the High-Z state during the cycle.
Power
-
On
After application of the V
CC
supply, an initial pause of
200 s is required followed by a minimum of eight initial-
ization cycles (any combination of cycles containing a
RAS
signal).
During power-on, it is recommended that
RAS
track with
V
CC
or be held at a valid V
IH
to avoid current surges.
IC41C4405x and IC41LV4405x Series
Integrated Circuit Solution Inc.
5
DR013-0B 10/17/2002
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
Parameters
Rating
Unit
V
T
Voltage on Any Pin Relative to GND
5V
-
1.0 to +7.0
V
3.3V
-
0.5 to +4.6
V
CC
Supply Voltage
5V
-
1.0 to +7.0
V
3.3V
-
0.5 to +4.6
I
OUT
Output Current
50
mA
P
D
Power Dissipation
1
W
T
A
Commercial Operation Temperature
0 to +70
o
C
Industrial Operation Temperature
-
40 to +85
o
C
T
STG
Storage Temperature
-
55 to +125
o
C
Note:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent
damage to the device. This is a stress rating only and functional operation of the device at these
or any other conditions above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for extended periods may affect
reliability.
RECOMMENDED OPERATING CONDITIONS
(Voltages are referenced to GND.)
Symbol
Parameter
Min.
Typ.
Max.
Unit
V
CC
Supply Voltage
5V
4.5
5.0
5.5
V
3.3V
3.0
3.3
3.6
V
IH
Input High Voltage
5V
2.4
-
V
CC
+ 1.0
V
3.3V
2.0
-
V
CC
+ 0.3
V
IL
Input Low Voltage
5V
-
1.0
-
0.8
V
3.3V
-
0.3
-
0.8
T
A
Commercial Ambient Temperature
0
-
70
o
C
Industrial Operation Temperature
-
40
-
85
o
C
CAPACITANCE
(1,2)
Symbol
Parameter
Max.
Unit
C
IN
1
Input Capacitance: A0-A10(A11)
5
pF
C
IN
2
Input Capacitance:
RAS
,
CAS
,
WE
,
OE
7
pF
C
IO
Data Input/Output Capacitance: I/O0-I/O3
7
pF
Notes:
1. Tested initially and after any design or process changes that may affect these parameters.
2. Test conditions: T
A
= 25
o
C, f = 1 MHz.