Bri
Lux 1W Light Source
BTP-187XXCQ-XX-XX
Package Dimension
[Note 1]
Features
Highest Lumen Per Watt
Long Operational Life
More Energy Efficient
IC Compatible
Low DC Voltage
Superior ESD Protection
Smallest Footprint
Applications
Accent Lighting
Automotive Exterior/Interior Light
High Power Back Light
Reading Light
Marine/Miner's Lighting
Portable Lighting
Tolerance: see spec Unit: mm
Optical Characteristics at T
a
=25C, I
F
=350mA
LED CHIP
Wavelength/CCT
Range (nm/K)
Drive
Voltage
Luminous
Flux
@350mA(lm)
PART NUMBER
MATERIAL
Lens
Color
Min/Max
Typ. Typ.
VIEW
ANGLE
2
1/2
(deg)
BTP-187NRCQ-XX-17
AlInGaP
Water Clear
620~635
2.60V
17 lm
[2]
90
BTP-187YECQ-XX-17
AlInGaP
Water Clear
585~595
2.60V
17 lm
[2]
90
BTP-187BLCQ-XX-08
AlInGaN
Water Clear
460~470
3.60V
6 lm
[2]
90
BTP-187GBCQ-XX-10
AlInGaN
Water Clear
470~480
3.60V
10 lm
[2]
90
BTP-187PGCQ-XX-15
AlInGaN
Water Clear
520~530
3.60V
15lm
[2]
90
BTP-187WHCQ-XX-30
AlInGaN
Water Clear
3000K 8000K
3.60V
30 lm
[2]
90
Note:
1) Picture for illustration purpose only. Please refer to outline dimension for actual package size.
2) Due to the CIE eye response curve in the wavelength range, the minimum luminous flux will vary over the wavelength range of
D
. For
example, luminous flux will vary from a minimum of 4.5lm at 460 to a typical of 15 lm at 480nm nm due to this effect.
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
Bri
Lux 1W Light Source
BTP-187XXCQ-XX-XX
Absolute Maximum Ratings at T
a
=25C
Parameter
Red/Yellow
White/Blue
DC Forward Current (mA)
[1]
300 350
Peak Pulsed Forward Current (mA)
350
500
Average Forward Current (mA)
300
300
Reverse Voltage (V)
5
5
LED Junction Temperature (C)
[3]
120 120
Thermal Resistance without heatsink (C/W)
80
80
Storage Temperature (C)
-20 to +80
-20 to +80
Operating Temperature (C)
-10 to +70
-10 to +70
Application Notes:
1.
Proper forward current must be observed to maintain the junction temperature below maximum
rating
2.
Although all products listed are class one ESD protection (+/- 1KV by HBM mode), care must be
fully taken when handling products
3.
Specification is subjected to change for improvements without notice.
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
Bri
Lux 1W Light Source
BTP-187XXCQ-XX-XX
Recommended Soldering Pattern
Important Notes:
The information contained herein is presented only as a Guide for the application of our
products. Brilliance Technologies assumes no responsibility for any infringement of intellectual
property or other rights of the third parties which may result from its use.
Brilliance Technologies continually improves the quality of our products. Nevertheless,
semiconductor devices in general can malfunction or fail due to their inherent electrical
sensitivity and vulnerability to physical stress. It is the responsible of the customer, when
using Brilliance Technologies products, to comply with the standard of safety in making a safe
design for the entire system, and to avoid situations in which a malfunction or failure of such
Brilliance Technologies products cause loss of human life, bodily injury or damage to property.
Brilliance Technologies products listed in this data sheet are intended for usage in general
electronics and/or non-commercial or industrial lighting products. These products are neither
intended nor warranted for usage in equipment that requires extraordinarily high quality and/or
reliability or a malfunction or failure of which may cause loss of human life or bodily injury.
In developing your design, please ensure that Brilliance Technologies products are used within
specified operating ranges as set forth in the most recent Brilliance Technologies data sheets.
BT-Rev. 1.0B20040917
Specifications are subject to change for improvement without notice.
Copyright 2003 Brilliance Technologies Co., Ltd. All rights reserved.
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
PDF 
ZIP