ChipFind - документация

Электронный компонент: 3315R-001-006

Скачать:  PDF   ZIP
*RoHS Directive 2002/95/EC Jan 27 2003 including Annex
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
3315 - 9 mm Square Sealed Incremental Encoder
Features
Miniature package for design flexibility
Long operating life
Conductive plastic element
Bushing or PC board mount
Quadrature output
RoHS compliant versions available*
Electrical Characteristics
Output ..........................................................................................................2-bit gray code, Channel A leads Channel B electrically turning clockwise (CW)
Closed Circuit Resistance ..............................................................................................................................................................................5 ohms maximum
Contact Rating ..........................................................................................................................................................................................TTL compatible loads
Insulation Resistance (500 VDC)........................................................................................................................................................1,000 megohms minimum
Dielectric Withstanding Voltage
Sea Level ..................................................................................................................................................................................................900 VAC minimum
Electrical Travel..........................................................................................................................................................................................................Continuous
Contact Bounce ..................................................................................................................................................................................5 milliseconds maximum
RPM (Operating) ..................................................................................................................................................................................................120 maximum
Environmental Characteristics
Operating Temperature Range ........................................................................................................................................-40 C to +125 C (-40 F to +257 F)
Storage Temperature Range............................................................................................................................................-55 C to +125 C (-67 F to +257 F)
Humidity....................................................................................................................................................................MIL-STD-202, Method 103B, Condition B
Vibration ..............................................................................................................................................................................................................................30 G
Contact Bounce ............................................................................................................................................................................5.0 millisecond maximum
Shock ................................................................................................................................................................................................................................100 G
Contact Bounce ............................................................................................................................................................................5.0 millisecond maximum
Rotational Life ......................................................................................................................................................................................100,000 cycles @ 6 PPR
25,000 cycles @ 16 PPR
IP Rating ..............................................................................................................................................................................................................................IP 67
Mechanical Characteristics
Mechanical Angle ............................................................................................................................................................................................360 Continuous
Running Torque ........................................................................................................................................................................3.53 N-cm (5 oz.-in.) maximum
Mounting Torque
Plastic Bushing..................................................................................................................................................................45.19 N-cm (4.0 lb.-in.) maximum
Metal Bushing ........................................................................................................................................................................79 N-cm (7.0 lb.-in.) maximum
Weight ..............................................................................................................................................................................................................4.5 gm (0.15 oz.)
Terminals ............................................................................................................................................................................................................Solderable pins
Soldering Condition
Manual Soldering ..................................................96.5Sn/3.0Ag/0.5Cu solid wire or no-clean rosin cored wire; 370 C (700 F) max. for 3 seconds
Wave Soldering............................................................................96.5Sn/3.0Ag/0.5Cu solder with no-clean flux; 260 C (500 F) max. for 5 seconds
Wash Processes ..........................................................For recommended wash processes, please refer to
http://www.bourns.com/pdfs/sldclen.pdf
Marking................................................................................................................................................Manufacturer's trademark, part number, and date code
Hardware ..................................................One lockwasher and one mounting nut are shipped with each encoder, except where noted in the part number.
Suggested Incremental Control Diagram
5 ms DELAY
DEBOUNCE
(MC 14490)
.0015 f
9
7
MAGNITUDE
(CUSTOMER LOGIC CIRCUITRY)
DECODE
LOGIC
UP/DOWN
COUNTER
DIRECTION
BINARY
OUTPUT
Quadrature Output Table
Clockwise
Channel A
Channel B
Channel C
*RoHS COMPLIANT
VERSIONS
AVAILABLE
3315 - 9 mm Square Sealed Incremental Encoder
Part Numbering System
3315 Y - 0 0 1 - 006 L
Model Number Designator
3315 = 9 mm Encoder
Terminal Style Designator
C =
In-line Straight Terminals Side Exit
R =
In-line Terminals Rear Exit
P =
5.08 mm x 2.54 mm Triangular Pattern Rear Exit
Y =
5.08 mm x 5.08 mm Triangular Pattern Rear Exit
Shaft End Designator
0 =
Shaft End Slotted
1 =
Shaft End Flatted
Shaft Length Designator
0 =
12.7 mm FMS Long Plastic Shaft (Available w/bushing only)
1 =
19.05 mm FMS Long Plastic Shaft (Available w/bushing only)
2 =
5.59 mm FMS (Bushingless version only)
Bushing Designator
1 =
6.35 mm x 6.35 mm Plastic
2 =
6.35 mm x 6.35 mm Ni Plated Brass
5 =
Bushingless (Board Level)
Pulses per Revolution Code
006 = 6 PPR
016 = 16 PPR
Terminals
L = RoHS compliant (100 % tin plated finish)
Blank = Standard (tin/lead plated finish)
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
3315 - 9 mm Square Sealed Incremental Encoder
Product Dimensions
A
A
A
A
C
C
C
C
B
B
B
B
A
C
B
COMMON DIMENSIONS
3315-001
Plastic Bushing
Slotted Shaft
COMMON DIMENSIONS
3315C-101
Plastic Flatted Shaft
3315C-001
3315Y-001
3315P-001
3315R-001
9.53 .25
(.375 .010)
9.53 .25
(.375 .010)
9.53 .25
(.375 .010)
9.53 .25
(.375 .010)
9.53 .25
(.375 .010)
.391 .38
(.154 .015)
9.53 .25
(.375 .010)
5.97 .89
(.235 .035)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .38
(.100 .015)
MOUNTING
SURFACE
4.83
(.190)
2.39
(.094)
5.08 .25
(.200 .010)
5.97 .89
(.235 .035)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
5.97 .89
(.235 .035)
5.97 .89
(.235 .035)
2.54 .25
(.100 .010)
.51 .05
(.020 .002)
SOLDER PLATED
COPPER PINS
DIA.
3.18 .05
(.125 .002)
DIA.
.64 .10
(.025 .004)
WIDE
.76 .25
(.030 .010)
DEEP
X
.51
(.020)
4 PLACES
DIA. MOUNTING
SURFACE
4.78
(.188)
7.62
(.300)
.38
(.015)
MIN.
STANDOFF
.76 .05 X .76
(.030 .002 X .030)
ANTI-ROTATION
BOSS
HIGH
R
6.35 .08
(.250 .003)
MOUNTING
DIA.
4.83 .25
(.190 .010)
4.83 .38
(.190 .015)
6.35 .08
(.250 .003)
MOUNTING DIA.
12.70 .64
(.500 .025)
FROM MOUNTING
SURFACE
5.18 .38
(.204 .015)
12.70 .64
(.500 .025)
ADJUSTMENT SLOT
4.75
(.187)
MIN. FULL
THREAD
6.35
(.250)
.38
(.015)
MIN.
STANDOFF
1/4-32 UNEF-2A
THREADED PLASTIC
BUSHING
MOUNTING
SURFACE
MOUNTING HOLE PATTERN
1.70 0.03
(.067 .001)
DIA.
6.53 0.03
(.257 .001)
DIA.
4.78
(.188)
MM
DIMENSIONS:
(IN.)
3315 - 9 mm Square Sealed Incremental Encoder
Product Dimensions
3315P-101
A
C
B
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
5.97 .89
(.235 .035)
4.83 .38
(.190 .015)
3315R-101
3315Y-101
C
A
B
C
A
B
2.54 .25
(.100 .010)
2.54 .38
(.100 .015)
5.08 .25
(.200 .010)
5.97 .89
(.235 .035)
5.97 .89
(.235 .035)
COMMON DIMENSIONS
3315-002
Metal Bushing
9.53 .25
(.375 .010)
9.53 .38
(.375 .015)
.51 .05
(.020 .002)
SOLDER PLATED
COPPER PINS
DIA.
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
5.97 .89
(.235 .035)
1/4-32 UNEF-2A
THREADED PLASTIC
BUSHING
MOUNTING
SURFACE
.38
(.015)
MIN.
STANDOFF
6.35 .08
(.250 .003)
MOUNTING DIA.
3.18 .05
(.125 .002)
DIA.
6.35
(.250)
.76
(.029)
12.70 .64
(.500 .025)
5.11 .25
(.201 .010)
6.35 .64
(.250 .025)
.64 .10
(.025 .004)
WIDE
.76 .25
(.030 .010)
DEEP
X
ADJUSTMENT SLOT
.76 .05 X .97
(.030 .002 X .038)
ANTI-ROTATION
BOSS
HIGH
R
DIA. MOUNTING
SURFACE
7.62
(.300)
.38
(.015)
MIN.
STANDOFF
.76
(.030)
2 PLCS.
3315C-002
5.08 .51
(.200 .020)
A
C
B
3315P-002
3315R-002
3315Y-002
A
C
B
A
C
B
A
C
B
2.54 .38
(.100 .015)
2.54 .38
(.100 .015)
5.08 .38
(.200 .015)
4.83 .38
(.190 .015)
5.97 .89
(.235 .035)
5.97 .89
(.235 .035)
MM
DIMENSIONS:
(IN.)
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
3315 - 9 mm Square Sealed Incremental Encoder
Product Dimensions
Bushingless
3315P-025
Bushingless
3315Y-025
9.53 .25
(.375 .010)
9.53 .25
(.375 .010)
9.53 .25
(.375 .010)
A
C
B
A
C
B
2.54 .25
(.100 .010)
2.54 .38
(.100 .015)
7.62 .20
(.300 .008)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
2.54 .25
(.100 .010)
5.97 .89
(.235 .035)
5.97 .89
(.235 .035)
5.08 .25
(.200 .010)
.51 .05
(.020 .002)
SOLDER PLATED
COPPER PINS
DIA.
DIA.
3.18 .05
(.125 .002)
5.59 .38
(.220 .015)
5.59 .38
(.220 .015)
DIA.
6.35 .20
(.250 .008)
DIA.
.51 .05
(.020 .002)
SOLDER PLATED
COPPER PINS
DIA.
2.54 .25
(.100 .010)
.38
(.015)
MIN. STANDOFF
.38
(.015)
MIN. STANDOFF
.64 .10
(.025 .004)
WIDE
.76 .25
(.030 .010)
DEEP
X
ADJUSTMENT SLOT
5.18 .64
(.204 .025)
5.18 .64
(.204 .025)
.51 .10
(.020 .004)
4.83 .38
(.190 .015)
.38
(.015)
MIN.
STANDOFF
.38
(.015)
MIN.
STANDOFF
MM
DIMENSIONS:
(IN.)
REV. 04/06