DC-DC CONVERTERS POLA Non-isolated
1
NEW Product
File Name: ptv05010w.pdf Rev (02): 16 Dec 2005
2 YEAR WARRANTY
All specifications are typical at nominal input, full load at 25 C unless otherwise stated
C
in
= 100 F and 10 F (Ceramic), C
out
= 0 F
SPECIFICATIONS
The PTV05010 is a non-isolated dc-dc converter from Artesyn under the Point of Load
Alliance (POLA) standard. The vertical mounting option of the PTV05010 module provides
performance in less than 20% of the space that is required by alternative solutions. The
Auto-TrackTM feature provides for sequencing between multiple modules, a function, which
is becoming a necessity for powering advanced silicon including DSP's, FPGA's and ASIC's
requiring controlled power-up and power-down. The PTV05010 has an input voltage of
4.5 Vdc to 5.5 Vdc and offers a wide 0.8 Vdc to 3.6 Vdc output voltage range with up to
8 A output current, which allows for maximum design flexibility and a pathway for future
upgrades.
8 A output current
5 V input voltage
Wide-output voltage adjust (0.8 Vdc to 3.6 Vdc)
Auto-trackTM sequencing*
Pre-bias start-up
Efficiencies up to 95%
Output ON/OFF inhibit
Vertical through-hole mounting
Point-of-Load-Alliance (POLA) compatible
Undervoltage lockout
Available RoHS compliant
*Auto-trackTM is a trade mark of
Texas Instruments
PTV05010
5 V i n s i n g l e o u t p u t
OUTPUT SPECIFICATIONS
Voltage adjustability
(See Note 4)
0.8-3.6 Vdc
Setpoint accuracy
(See Note 8)
2.0% Vo
Line regulation
5 mV typ.
Load regulation
5 mV typ.
Total regulation
(See Note 8)
3.0% Vo
Minimum load
0 A
Ripple and noise
20 MHz bandwidth
15 mV pk-pk
Temperature co-efficient
-40 C to +85 C
0.5% Vo
Transient response
70 s recovery time
(See Note 5)
Overshoot/undershoot 100 mV
INPUT SPECIFICATIONS
Input voltage range
(See Note 3)
4.5-5.5 Vdc
Input standby current
5 mA typ.
Remote ON/OFF
(See Note 1)
Positive logic
Undervoltage lockout
(Increasing)
4.3 V typ.
Track input current
Pin 9 (See Notes 6, 7)
-0.13 mA
International Safety Standard Approvals
UL/cUL CAN/CSA-C22.2 No. 60950
File No. E174104
TV Product Service (EN60950) Certificate No. B 04 06 38572 044
CB Report and Certificate to IEC60950, Certificate No.
US/8292/UL
EMC CHARACTERISTICS
Electrostatic discharge
EN61000-4-2, IEC801-2
Conducted immunity
EN61000-4-6
Radiated immunity
EN61000-4-3
GENERAL SPECIFICATIONS
Efficiency
(See Efficiency Table)
95% max.
Insulation voltage
Non-isolated
Switching frequency
55-650 kHz
600 kHz typ.
Approvals and
EN60950
standards
UL/cUL60950
Material flammability
UL94V-0
Dimensions
(L x W x H)
22.86 x 8.38 x 10.16 mm
0.90 x 0.330 x 0.400 in
Weight
2.5 g (0.9 oz)
MTBF
Telcordia SR-332
5,000,000 hours
ENVIRONMENTAL SPECIFICATIONS
Thermal performance
Operating ambient,
-40 C to +85 C
(See Note 2)
temperature
Non-operating
-40 C to +125 C
PROTECTION
Overcurrent
Auto reset
12 A typ.
File Name: ptv05010w.pdf Rev (02): 16 Dec 2005
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
DC-DC CONVERTERS POLA Non-isolated
2
NEW Product
N
No
otte
es
s
1
Remote ON/OFF. Positive logic
ON:
Pin 7 open; or V > (Vin - 0.5 V)
OFF:
Pin 7 GND; or V < 0.6 V
2
See Figure 1 for safe operating curve.
3
A 100 F electrolytic input capacitor is required for proper operation as
well as a 10F high-frequency ceramic capacitor. The electrolytic -
capacitor must be rated for a minimum of 300 mArms of ripple current.
4
An external output capacitor is not required for basic operation. Adding
100 F of distributed capacitance at the load will improve the transient
response.
5
1 A/s load step, 50 to 100% I
omax
, C3 = 100 F.
6
If utilized Vout will track applied voltage by 0.3 V (up to Vo set point).
7
The pre-bias start-up feature is not compatible with Auto-TrackTM. This is
because when the module is under Auto-TrackTM control, it is fully active
and will sink current if the output voltage is below that of a back-feeding
source. Therefore to ensure a pre-bias hold-off, one of the following two
techniques must be followed when input power is first applied to the
module. The Auto-TrackTM function must either be disabled, or the
module's output held off using the Inhibit pin. Refer to Application Note
195 for more details.
8
The set-point voltage tolerance is affected by the tolerance and stability
of Rset. The stated limit is unconditionally met if Rset has a tolerance of
1% with 100/
C or better temperature stability.
9
To order Pb-free (RoHS compatible) through-hole parts replace the
mounting option `H' with `D', e.g. PTV05010WAD.
10
NOTICE: Some models do not support all options. Please contact your
local Artesyn representative or use the on-line model number search tool at
http://www.artesyn.com/powergroup/products.htm to find a suitable
alternative.
OUTPUT
INPUT
OUTPUT
OUTPUT
OUTPUT
EFFICIENCY
REGULATION
MODEL
POWER
VOLTAGE
VOLTAGE
CURRENT
CURRENT
(MAX.)
LINE
LOAD
NUMBER
(9,10)
(MAX.)
(MIN.)
(MAX.)
(2)
28.8 W
4.5-5.5 Vdc
0.8-3.6 Vdc
0 A
8 A
95%
5 mV
5 mV
PTV05010
PTV05010
5 V i n s i n g l e o u t p u t
Part Number System with Options
Product Family
Point of Load Alliance
Compatible
Mounting Version
V = Vertical
Mounting Option
(9)
D = Horizontal Through-Hole (Matte Sn)
H = Horizontal Through-Hole (Sn/Pb)
The ultra-wide output voltage trim range offers major advantages to users who
select the PTV05010. It is no longer necessary to purchase a variety of
modules in order to cover different output voltages. The output voltage can be
trimmed in a range of 0.8 Vdc to 3.6 Vdc. When the PTV05010 converter
leaves the factory the output has been adjusted to the default voltage of 0.8 V.
O
Ou
uttp
pu
utt V
Vo
olltta
ag
ge
e A
Ad
djju
us
sttm
me
en
ntt o
off tth
he
e P
PT
TV
V0
05
50
01
10
0 S
Se
erriie
es
s
Output Current
01 = 8 A
Input Voltage
05 = 5 V
Mechanical Package
Always 0
P T V 0 5 0 1 0 W A H
Pin Style
A = Through-Hole Std. Pin Length (0.150")
Output Voltage Code
W = Wide
EFFICIENCY TABLE (I
O
= I
O
max)
OUTPUT VOLTAGE
EFFICIENCY
Vo = 3.3 V
95
Vo = 2.5 V
93
Vo = 1.8 V
90
Vo = 1.5 V
89
Vo = 1.2 V
87
Vo = 1.0 V
85
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
DC-DC CONVERTERS POLA Non-isolated
3
NEW Product
File Name: ptv05010w.pdf Rev (02): 16 Dec 2005
E
F
F
I
C
I
E
N
C
Y
(
%
)
OUTPUT CURRENT (A)
3.3V
2.5V
1.8V
1.2V
70
80
90
100
0
2
6
Vout
60
50
4
8
0.8V
T
E
M
P
E
R
A
T
U
R
E
(
C
)
OUTPUT CURRENT (A)
20
30
40
50
60
70
80
90
0
2
6
4
8
Nat conv
100 LFM
200 LFM
400 LFM
Figure 2 - Efficiency vs Load Current
Vin = 5 V (See Note B)
Figure 1 - Safe Operating Area
Vin = 5 V, Output Voltage = 3.3 V (See Note A)
PTV05010
5 V i n s i n g l e o u t p u t
N
No
otte
es
s
A
SOA curves represent the conditions at which internal components are
within the Artesyn derating guidelines.
B
Characteristic data has been developed from actual products tested at
25 C. This data is considered typical data for the converter.
2
3
C2
10uF
Ceramic
(Required)
C3
100uF
Optional
Vin
Vo
Rset
1%
0.05W
Track
C1
100uF
(Required)
GND
Inhibit
GND
L
O
A
D
PTVxx010
5
4
1
6
7
8
GND
Inhibit
Vo Adj
Vo
Vin
Track
Figure 3 - Standard Application
PIN CONNECTIONS
PIN NO.
FUNCTION
1
Ground
2
Vout
3
Vout
4
Vo Adjust
5
Track
6
Ground
7
Inhibit
8
Vin
File Name: ptv05010w.pdf Rev (02): 16 Dec 2005
Please consult our website for the following items:
Application Note
www.artesyn.com
Datasheet Artesyn Technologies 2005
The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising
from printing errors or inaccuracies. The information and specifications contained or described herein are subject to change in any manner at any time without notice. No rights under any patent
accompany the sale of any such product(s) or information contained herein.
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
DC-DC CONVERTERS POLA Non-isolated
4
NEW Product
FRONT VIEW
SIDE VIEW
0.330
0.008
(8.38
0.20)
0.100 (2.54)
0.100 (2.54)
1
2
3
4
6
5
7
8
PCB
0.150 (3.81)
0.400 (10.16)
0.900 (22.86)
0.025 (0.64)
Min 8 Places
Plated Through Hole
Dimensions in Inches (mm)
Tolerances (unless otherwise specified)
2 Places
0.030 (
0.76)
3 Places
0.010 (
0.25)
0.020 (0.51)
Figure 4 - Mechanical Drawing
PTV05010
5 V i n s i n g l e o u t p u t
PDF 
ZIP