DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Agilent HCPL-8100/0810
High Current Line Driver
Data Sheet
Connection Diagram
Description
The HCPL-8100 and HCPL-
0810 are low-cost high current
line drivers. With a 5 V single
supply, they deliver up to 1
A
PP
current. This is ideal for
high current applications such
as a Powerline modem.
The HCPL-8100 and HCPL-
0810 are internally protected
against over-temperature
conditions through thermal
shutdown. Under-voltage or
over-load condition is sensed
by internal detection circuit
Features
1 A
PP
driving current
3.5 MHz gain bandwidth product
--
--
- 60 dB maximum harmonic
distortion
Load detection function
Under-voltage detection
Over-temperature shutdown
5 V single supply
Temperature range:
--
--
-40C to
+85C
Suitable for FCC Part 15 and
EN50065-1 compliant design
Applications
Automatic meter reading (AMR)
Powerline modem
General purpose line driver
Signal conditioning
Digital-to-analog converter
buffers
and indicated by Status pin
output. In addition, with the
transmit enable (Tx-en) input,
the line driver output stage
can be disabled to reduce
power dissipation when not
operating.
The HCPL-8100 and HCPL-
0810 are specified for
operation over extended
temperature range from
-40C to +85C. The HCPL-
8100 is available in DIP-8
package, and the HCPL-0810 is
available in SO-8 package.
PLM
Transceiver
STATUS
TX -EN
TX
Filter
HCPL-8100/0810
1
2
3
4
5
6
7
8
Status
Tx -en
Tx -in
R
ref
GND
GND
V
CC
Tx -out
N
L
5 V
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and /or degradation which may be induced by ESD.
2
Package Pin Out
Block Diagram
Pin Descriptions
Ordering Information
Specify part number followed by option number (if desired).
Example:
HCPL-8100
HCPL-0810-XXX
No option = SO-8 package, 100 units per tube.
500 = Tape and Reel Packaging Option, 1500 units per reel.
Standard 8-pin DIP package, 50 units per tube.
Pin No. Symbol
Function
Description
1
Status
Line condition
detection
A logic high indicates line conditions
such as
- under-voltage when V
CC
< 4 V
- load detection when I
Tx-out
<
-0.25 A
- over-temperature (thermal
shutdown)
2
Tx-en
Transmit enable
A logic high enables the Tx-out;
A logic low disables the Tx-out and
changes it to high impedance state
3
Tx-in
Transmit input
Transmit signal input
4
R
ref
Resistor reference
Sets line driver biasing current,
typically 24 k
5, 6
GND
Power supply ground Power supply and signal ground
7
V
CC
5 V power supply
5 V power supply
8
Tx-out
Transmit output
Transmit signal output, to be enabled
by Tx-en
1
Tx-en
Status
Tx-in
R ref
Tx-out
V
CC
GND
GND
2
3
4
5
6
7
8
Amp
Under-Volt
Detection
Load
Detection
Over-Temp
Detection
Status
Output
Tx-in
Tx-en
Status
R
ref
GND
2
1
7
3
4
8
6
GND
5
V
CC
Tx-out
3
Package Outline Drawings
HCPL-8100 Standard 8-pin DIP package
DIMENSIONS IN MILLIMETERS AND (INCHES)
HCPL-0810 Small Outline SO-8 Package
9.50
0.05
(0.374
0.002)
1.524 (0.060) MAX.
1.19 (0.047) MAX.
A 8100
YYWW
DATE CODE
1.094
0.320
(0.037
0.013)
2.54
0.25
(0.100
0.010)
0.381 (0.015) MIN.
0.555 (0.022) MAX.
3.92 (0.155) MAX.
3.05 (0.120) MIN.
5
6
7
8
4
3
2
1
5 TYP.
0.20 (0.008)
0.35 (0.014)
7.87
0.25
(0.310
0.010)
6.62
0.05
(0.260
0.002)
DIMENSIONS IN MILLIMETERS AND (INCHES)
4
Parameter
Symbol
Min.
Max.
Unit
Storage Temperature
T
S
-55
125
C
Ambient Operating Temperature
T
A
-40
85
C
Junction Temperature
T
J
150
C
Supply Voltage
V
CC
-0.5
5.5
Volts
Output Voltage
V
O
-0.5
V
CC
Volts
Tx-in Voltage
V
Tx-in
-0.5
V
CC
Volts
Tx-en Voltage
V
Tx-en
-0.5
V
CC
Volts
Solder Reflow Temperature Profile
(See Solder Reflow Temperature Profile Section)
Recommended Operating Conditions
Absolute Maximum Ratings
Solder Reflow Temperature Profile
0
TIME (SECONDS)
TEMPERATURE (
C)
200
100
50
150
100
200
250
300
0
30
SEC.
50 SEC.
30
SEC.
160
C
140
C
150
C
PEAK
TEMP.
245
C
PEAK
TEMP.
240
C
PEAK
TEMP.
230
C
SOLDERING
TIME
200
C
PREHEATING TIME
150
C, 90 + 30 SEC.
2.5
C 0.5
C/SEC.
3
C + 1
C/- 0.5
C
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
PREHEATING RATE 3
C + 1
C/- 0.5
C/SEC.
REFLOW HEATING RATE 2.5
C 0.5
C/SEC.
Parameter
Symbol
Min.
Typ.
Max.
Unit
Ambient Operating Temperature
T
A
-40
25
85
C
Supply Voltage
V
CC
4.75
5
5.25
V
5
Electrical Specifications
Unless otherwise noted, for sinusoidal waveform input and reference resistor R
ref
= 24 k
, all typical values are
at T
A
= 25C and V
CC
= 5 V; all Minimum/Maximum specifications are at Recommended Operating Conditions.
Notes:
1. Threshold of falling V
CC
with hysteresis of 0.2 V (typ.).
2. Threshold of rising junction temperature with hysteresis of 20C (typ.).
3. See Application Information section for more information on the load detection feature.
4. See Figure 3 for the plot of supply current versus Tx output current.
Parameter
Symbol
Min.
Typ.
Max.
Unit
Test Condition
Fig.
Note
V
CC
Supply Current
I
CC
1.2
2
mA
V
Tx
-en
= 0 V, V
Tx
-in
= 0 V
PP
,
Tx-out no load
1
20
45
mA
V
Tx
-en
= 5 V, V
Tx
-in
= 0 V
PP
,
Tx-out no load
2, 3
V
CC
Under Voltage
Detection
V
UVD
3.8
4.0
4.3
V
1
Junction Over-
Temperature Threshold
150
C
2
Load Detection
Threshold
0.5
A
PP
V
Tx
-en
= 5 V, V
Tx
-in
= 1.25 V
PP
,
f = 132 kHz, Gain =
- 2, R
L
= 2.5
12, 13
3
Status Logic High
Output
V
OH
V
CC
-1
V
CC
V
V
CC
= 3.5 V, I
OH
=
- 4 mA
Status Logic Low
Output
V
OL
0
0.8
V
V
CC
= 5 V, I
OL
= 4 mA
Power Supply
Rejection Ratio
PSRR
72
dB
50 Hz ripple, V
ripple
= 200 mV
PP
,
V
Tx
-en
= 5 V, V
Tx
-in
= 0 V
PP
, Tx-out no load
DC Bias Voltage
V
Bias
2.27
V
V
Tx
-en
= 5 V, Tx-out no load
Output Impedance
Z
O
12
k
V
Tx
-en
= 0 V, V
Tx
-in
= 0 V
PP
,
open loop, f = 132 kHz
0.5
V
Tx
-en
= 5 V, V
Tx
-in
= 0 V
PP
, f = 132 kHz
Gain Bandwidth
Product
GBW
3.5
MHz
V
Tx
-en
= 5 V, V
Tx
-in
= 1 V
PP
,
R
L
= 50
4, 14
Transmit Enable
Threshold Voltage
V
th, Tx
0.8
2.4
V
V
Tx
-in
= 1 V
PP
, f = 132 kHz,
Tx-out no load
Tx Enable Time
t
Tx-en
0.9
s
V
Tx
-en
= 5 V, V
Tx
-in
= 1.75 V
PP
,
f = 132 kHz, Tx-out no load
11, 15
Tx Disable Time
0.2
s
V
Tx
-en
= 0 V, V
Tx
-in
= 1.75 V
PP
,
f = 132 kHz, Tx-out no load
15
2nd Harmonic
Distortion
HD2
-65
-60
dB
V
Tx
-en
= 5 V, V
Tx
-out
= 3.5 V
PP
, f = 132 kHz,
Gain =
-2, R
ref
= 24 k
, R
L
= 50
5-10, 16
3rd Harmonic
Distortion
HD3
-75
-65
dB
Output Current
I
O
1
A
PP
V
Tx
-en
= 5 V, f=132 kHz
4
Thermal Resistance
(HCPL-8100)
JA
100
C/W 1 oz. trace, 2-layer PCB, still air, T
A
= 25C
60
C/W 1 oz. trace, 4-layer PCB, still air, T
A
= 25C
Thermal Resistance
(HCPL-0810)
JA
138
C/W 1 oz. trace, 2-layer PCB, still air, T
A
= 25C
70
C/W 1 oz. trace, 4-layer PCB, still air, T
A
= 25C
PDF 
ZIP